R
K0022-2 8/02
FA560VKP
VOICE KEYPAD
Installation and Setup Guide
GENERAL INFORMATION
The FA560VKP is an addressable remote keypad designed for
use with First Alert control panels and provides the following
features:
•
Backlit Display
•
Voice Chime
•
Programmable Function Keys
•
Voice Status
•
Built-in Sounder
•
Message Center
Notes:
•
When used with the FA148CP/FA168CPS control panels,
address 16 must be assigned to the first keypad. Additional
keypads must be assigned to address 17–23. Refer to Setting
The Keypad Options on next page.
•
Keypad keys are continuously backlit for convenience.
•
Permanent display backlighting is an option on some
controls (refer to the control panel’s instructions for details).
•
Voice Chime should only be enabled when used with control
panels that support the "chime by zone" mode (e.g.,
FA148CP/FA168CPS). This mode must be enabled at the
control panel. Refer to the control panel's installation and
setup guide for information on how to program the chime
mode.
•
Use only zone descriptors supported by this keypad. If using
zone descriptors not supported by this keypad, you must
turn voice status and voice chime off. Table 1 is a list of
applicable zone descriptors and index entries.
Refer to
the
control panel’s installation and setup guide for information
about how to program zone descriptors.
KEYPAD DISPLAYS AND LEDS
The keypad has the following display features:
•
2-Line, 16-Character, Alpha/Numeric Display
•
Custom Zone Descriptors
The following table identifies the keypad LEDs and associated
functions:
LED
Function
ARMED
Lights red when the system is armed in any mode.
READY
Lights green when the system is "ready" to be
armed.
MESSAGE
Flashes red when message waiting or lights red
(steady) when in record mode.
PROGRAMMABLE FUNCTION KEYS
The keypad's programmable function keys [A, B, C] are
normally used for keypad panic functions, but they can be
programmed for other special functions instead. If they are
programmed for other special functions, the associated keypad
key pairs still provide the respective panic alarm (if
programmed). Refer to the control panel’s Installation & Setup
Guide for details.
Function
Keys
Equivalent Key Pairs
A
[1] and [
✱
]
B
[
✱
] and [#]
C
[3] and [#]
D
NONE
•
Function keys must be held down for at least 2
seconds to activate the programmed function.
•
If functions other than panics are assigned to
the programmable function keys, programmed
panics must be initiated by pressing the
programmed key pair.
FUNCTION KEY LABELS
A set of adhesive-backed labels with some typical function
symbols (i.e., fire, police, personal emergency, etc.) is provided.
These labels can be placed on or next to the keys to identify
each key's function for the end user (as determined by the
capability and programming of the control panel; refer to the
installation and setup guide for the control panel).
A
B
C
D
6
4
7
BYPASS
9
CHIME
#
3
STAY
5
TEST
8
CODE
0
2
AWAY
1
OFF
MAX
READY
INSTANT
*
RECORD
STATUS
ARMED MESSAGEREADY
PLAY
VOLUME
VOICE
FUNCTION
FA560VKP-002-V1
WIRING AND INSTALLATION
Keypads can be surface mounted using drywall anchors or to a
single- or double-gang electrical box.
1.
Remove the case back
by pushing in each of the two
"snaps" along the keypad’s bottom edge and pulling the
case apart.
2.
Route wiring from the control panel
through the
opening in the case back.
3.
Mount the case back
to a wall or electrical box.
4.
Wire directly from the keypad’s terminal block
to the
terminal block on the control board. (Refer to the following
Wiring Table.)
FA560VKP Wiring Table
Keypad
Control Panel
Wire Color
Y
Data Out
Yellow
+
+ Aux. Pwr
Red
–
– Aux Pwr (GND)
Black
G
Data In
Green
5.
Reattach the keypad
to the case back.
6.
Remove the clear protective film
from the LCD display.
To Next Page
Need help?
General
