Lit. No. 41298, Rev. 01 February 15, 2019
25
JOYSTICK CONTROL WITH SECURITY GUARD™ SNOWPLOW ANTI-THEFT SYSTEM
SECURITY GUARD System
Activation & Establishing a 4-Digit Security Code
NOTE: The snowplow must be attached to the
vehicle and all the electrical connections must
be connected prior to activating the security
code function.
1. Turn the vehicle ignition switch to the "ON" or
"ACCESSORY" position. (It is not necessary to
start the vehicle.)
2. Verify the control power indicator is OFF. If the
power indicator light is red, the control is ON.
Slide the ON/OFF switch to "OFF" to turn the
control OFF.
3. To activate the SECURITY GUARD mode,
move the control lever into the #1 position four
consecutive times, and then in the direction
of the #4 position four consecutive times
(sequence:
1, 1, 1, 1, 4, 4, 4, 4). The green FLOAT light will
fl ash quickly and the red POWER light will turn
ON indicating the system is ready to accept
your 4-digit security code.
Enter your 4-digit security code by moving the
control lever into the position of any of the eight
following positions: UP, DOWN, LEFT, RIGHT,
1, 2, 3, or 4.
Once you have entered your 4-digit security
code, the FLOAT light will stop fl ashing and the
POWER light will turn OFF. This indicates that
your 4-digit security code is entered and stored
in the SECURITY GUARD system.
Manual Unlock
If the SECURITY GUARD system is activated and
you are using a HT Series™ control with a different
4-digit code than the established security code,
you will be required to manually enter the 4-digit
security code before operating a locked snowplow.
1. Turn the vehicle ignition to the "ON" or
"ACCESSORY" position.
2. Slide the control switch to the "ON" position.
3. The POWER light will fl ash rapidly, indicating
that the snowplow is locked.
4. Enter the 4-digit security code.
5. After entering the correct security code, the
POWER light will change from fl ashing rapidly to
a solid light to indicate the snowplow has been
successfully unlocked.
4. Once a 4-digit security code is established,
the SECURITY GUARD system will recognize
any control that has been programmed with
the same 4-digit security code. If a control
not programmed with the correct 4-digit
security code is connected to the system,
the established security code will have to be
entered manually before the snowplow can be
activated (see the Manual Unlock procedure).
NOTE: If the control POWER switch is turned ON
prior to completing the programming procedure,
your 4-digit security code will be cancelled.
NOTE: If the plow/vehicle electrical connection
is lost or disconnected, the SECURITY GUARD
system will reset, requiring any HT Series control
that is not programmed with the established
4-digit security code to manually re-enter the
security code to activate the snowplow.
Clearing an Established 4-Digit Security Code
1. Turn the vehicle ignition switch to the "ON" or
"ACCESSORY" position.
2. If the snowplow is locked (the control POWER
light will be fl ashing at a fast rate), unlock the
snowplow by following the Manual Unlock
procedure.
3. Slide the control switch to the "OFF" position.
Verify that the power indicator is OFF.
4. With the control OFF, move the control lever
to the #2 position four consecutive times,
and then to the #3 position four consecutive
times. This sequence (2, 2, 2, 2, 3, 3, 3, 3)
will clear the 4-digit security code from the
SECURITY GUARD system. The FLOAT light
will fl ash to indicate that the 4-digit security
code was cleared.
NOTE: To enter a new 4-digit security code see
Activation & Establishing a 4-Digit Security
Code.
To Next Page
Loading...
