EN-3
IMPORTANT
To ensure optimal and proper functioning of your 07 Series Fluval External Filter, regular maintenance is required. Failure to do so
may result in the failure of the filter and will invalidate your warranty. Additionally, regular cleaning and maintenance will greatly
reduce or completely prevent faults and reduction in performance. Please refer to the maintenance schedule below.
RECOMMENDED MAINTENANCE FREQUENCY
COMPONENTS MONTHLY EVERY 3 MONTHS EVERY 6 MONTHS YEARLY
Magnetic Impeller & Impeller Well
1,4,6
Check & Clean Replace (Impeller only)
Ceramic Shaft
4
Check & Clean Replace
Intake Stem/Strainer
3
Check & Clean
Ribbed Hosing Check & Clean
Primer Assembly with Primer Cover Clean & Lubricate
Motor Head Gasket
2, 5
Clean & Lubricate Replace
AquaStop O-ring Gaskets Clean & Lubricate
Quick Clear Replace
Bio-Foam Check & Clean Replace
Bio-Foam+ Check & Clean Replace
Bio-Foam Max Check & Clean Replace
BIOMAX Rinse with aquarium water Replace Half Quantity
Pre-Filter Replace Half Quantity
BIOTERRA Rinse with aquarium water Replace Half Quantity
Carbon Replace
Ammonia Remover Replace
Zeo-Carb Replace
Phosphate Remover (Pad) Replace
Nitrite Remover (Pad) Replace
Ammonia Remover (Pad) Replace
To ensure constant presence of beneficial bacteria, never replace all media at the same time.
MODEL 107 207 307 407
AQUARIUM*
10-30 US Gal
40-130 L
20-45 US Gal
60-220 L
40-70 US Gal
90-330 L
50-100 US Gal
150-500 L
PUMP PERFORMANCE
145 US Gal/h
550 L/h
206 US Gal/h
780 L/h
303 US Gal/h
1150 L/h
383 US Gal/h
1450 L/h
VERTICAL PRE-FILTER 514 cm 803 cm 803 cm 1074 cm
BASKET VOLUME 1.2 L 1.8 L 3.1 L 4.2 L
TOTAL CHAMBER VOLUME 2.0 L 3.1 L 4.5 L 6.0 L
CANISTER VOLUME 3.9 L 5.3 L 7.3 L 9.2 L
FILTER DIMENSIONS
7.5” x 7” x 13.7”
19 x 18 x 35 cm
7.5” x 7” x 16.5”
19 x 18 x 42 cm
9.5” x 7” x 16.5”
24 x 18 x 42 cm
9.5” x 7” x 19.3”
24 x 18 x 49 cm
FILTER CIRCULATION**
95 US Gal/h
360 L/h
121 US Gal/h
460 L/h
206 US Gal/h
780 L/h
245 US Gal/h
930 L/h
MAX WATER COLUMN HEIGHT 1.45 m 1.45 m 1.75 m 2.25 m
WATTAGE – 120V/60Hz:
WATTAGE – 230-240V/50Hz:
10 W 10 W
16 W
15 W
23 W
20 W
*Aquarium recommendations are based on North American (US Gal) or European (L) standard aquarium usage
**Flow rates were measured with intake and output hoses of the same length
1. Ensure Impeller Cover is fitted right way up when replacing.
2. Lubricate Motor Head (“O” Ring) gasket using an inert lubricant
(i.e. Fluval Silicone Lubricant #A325 or vegetable oil). Do NOT use
petroleum jelly based products.
3. Pipes will gradually block with protein slime and waste.
4. Yearly replacement ensures optimal performance.
5. The Motor Head Gasket (“O” Ring) will deteriorate over time and
must be replaced yearly to avoid the potential for leaks.
6. Impeller will wear out over time. As a preventative step, replace
yearly.
To Next Page
Loading...
Need help?
General
