Fly Sky FGr4 User Manual

FGr4
接收机 Receiver
http://www.flysky-cn.com
Copyright ©2018 Flysky Technology co., ltd
FGr4 采用 AFHDS 3（第三代自动跳频数字系统），单天线双向
传输，它独特设计可节省安装空间，可输出标准 PPM 信号和 i-BUS
信号。
FGr4 adopts AFHDS 3, Flysky's third-generation automatic
frequency hopping digital system. It uses a single-antenna
bidirectional transmission system and is uniquely designed
to save space and output standard PPM and i-BUS signals.
产品介绍
Introduction
接收机概览
Receiver overview
用于连接接收机与模型的各个部件。
SENS：连接各传感器。
SENVO：连接 i-BUS 模块，扩展通道。
CH 1- CH 4：连接舵机、电源或其他各部件。
BIND：连接对码线。
Ports used to connect the receiver to the various
components.
SENS: Connects to sensors.
SENVO: Connectsto the i-BUS module for channel
expansion.
CH 1 - CH 4: Connects the servos, power supply or other
components.
BIND: For bind cable.
注意事项：
使用前必须确保本产品与模型安装正确，否则可能导致模型发生严重损坏。
关闭时，请务必先关闭接收机电源，然后关闭发射机。如果关闭发射机电源时接收机仍然在工作，将有可能导致遥控设备失控或者引
擎继续工作而引发事故。
确保接收机安装在远离电机，电子调速器或电子噪声过多的区域。
接收机天线需远离导电材料，例如金属棒和碳物质。为了避免影响正常工作，请确保接收机和导电材料之间至少有 1 厘米以上的距离。
准备过程中，请勿连接接收机电源，避免造成不必要的损失。
Attention:
Make sure the product is installed and calibrated correctly, failure to do so may result in serious injury.
Make sure the receiver's battery is disconnected before turning off the transmitter, failure to do so may lead to unintended operation
or loss of control.
Make sure the receiver is mounted away from motors, electronic speed controllers or any device that emits excessive electrical noise.
Keep the receiver's antenna at least 1cm away from conductive materials such as carbon or metal.
Do not power on the receiver during the setup process to prevent loss of control.
对码
Binding
1. 将对码线插入 BIND 接口；
2. 将电源线插入其他任意接口，接收机指示灯快闪表示进入对码
状态；
3. 将发射机进入对码状态；（发射机进入对码状态的方式可能不
同，请根据发射机的使用说明书进行操作）
4. 当接收机指示灯变为慢闪时，将对码线和电源线从接收机上取
下；
5. 将电源线重新连接至接收机，接收机指示灯常亮表示对码成功；
6. 检查发射机、接收机、模型是否正常工作。如需重新对码，请
重复以上步骤重新对码。
1. Insert the bind cable into the receivers BIND port;
2. Plug the power cable into any other port, and the the
receiver's LED will start to 󽗊ash indicating that it has entered
bind mode.
3. Put the transmitter into bind mode; (See the transmitter's
instruction manual for more information)
4. Binding is successful when the receiver's LED starts to 󽗊ash
slowly. Remove the power and bind cables from the receiver.
5. Reconnect the power cable to the receiver.
6. Check to make sure that the transmitter and receiver are
working as expected, if there are any issues or unexpected
operation follow the steps above to bind again.
SENS
SENVO
CH 1-CH 4
BIND
天线
LED

Fly Sky FGr4 Specifications

General

Frequency	2.4GHz
Channels	4
PWM Channels	4
Protocol	AFHDS 2A
Online Update	No
Modulation	GFSK
Antenna Type	Diversity antenna
Data Output	PPM
Temperature Range	-10°C to +60°C
Compatibility	Flysky transmitters

Summary

FGr4 Introduction

FGr4 Overview

FGr4 is Flysky's third-generation automatic frequency hopping digital system using a single-antenna bidirectional transmission.

Receiver Overview

Connecting Receiver Components

Parts to connect the receiver to models: SENSC for sensors, SENVO for i-BUS module, CH 1-4 for servos/power, and BIND for bind cable.

Precautions and Warnings

Installation Safety

Ensure correct installation before use to prevent severe model damage. Improper installation can lead to damage.

Environmental Considerations

Ensure receiver is in areas away from electrical appliances and electronic noise to prevent interference.

Mounting and Interference

Mount receiver away from electronics or motors. Avoid co-location with other transmitters.

Binding Procedure

Binding Steps

Procedure to bind the receiver to the transmitter: connect bind cable, power on transmitter, then receiver.

Product Specifications

Key Features

Details number of channels, model type, data output, frequency range, transmission power, protocol, modulation, and antenna.

Technical Details

Specifies input power, display, online update capability, dimensions, weight, and certifications.

Certification and Compliance

FCC Compliance

Statement on FCC compliance, conditions for operation, and measures to correct interference.

EU Declaration of Conformity

Declaration of compliance with RED 2014/53/EU, with link to full text.

RF Exposure Compliance

Compliance with FCC radiation exposure limits and minimum installation distance requirements.

Environmental Disposal

Instructions for environmentally friendly disposal of old electrical appliances.