Fly Sky FS-RM003 - User Manual

L
E
D
UP
DATE
F
S I
FS-RM003
2.4 G
http://www.flysky-cn.com
Copyright ©2017 Flysky Technology co., ltd
Function:
Instroduction
The FS-RM003 uses binding as well as a 2.4GHz frequency hopping digital transmission method to cut down on
external interference.
Overview
Bind LED
Bind Button
PPM
GND
VCC
GND
NC
PPM Port： PPM signal input。
GND: Ground。
VCC: Power。
接口
Before use: Make sure that the product is installed and working correctly.
Do not use the product at night or during bad weather conditions, like rain or thunderstorms. It can cause erratic
operation or loss of control.
Do not use the product when visibility is limited.
Do not expose the product to rain or snow. Any exposure to moisture (water or snow) may cause erratic operation or
loss of control.
Interference may cause loss of control. To ensure the safety of you and others, do not operate in the following places:
1. Near any site where other radio control activity may occur;
2. Near people or roads;
3. On any pond/lake when passenger boats are present;
4. Near power lines or communication broadcasting anten- nas.
Precautions
Specification
Frequency Range： 2.408-2.475GHz
Band width： 500KHz
Number of bands： 135
Transmitter Power： ≤20dBm（For Europe）
2.4G Protocol： AFHDS 2A
Antenna Length： 26mm
User Manual
Weight： 41g
Input power： 4.5-18V
Size： 178*52*40mm
Color： Black
Certification： CE, FCC
The LED indicator will flash indicating that bind mode is active.
The LED indicator will stop flashing and remain solid if binding is successful
If the transmitter and receiver are unable to bind the LED will flash slowly.
Before binding first make sure that the 2.4GHz transmitter module is installed correctly.
To enter bind mode press and hold the Bind button while the system is powered on.
The LED will turn off after 10 seconds if binding is successful.

Summary

Introduction to FS-RM003

Safety Precautions

Operational Safety Guidelines

Avoid using the product in bad weather, at night, or with limited visibility to prevent erratic operation or loss of control.

Interference Avoidance Measures

Do not operate near other radio activities, people, roads, water bodies, or power lines to prevent interference and loss of control.

Product Overview

Hardware and Port Identification

Diagram of the module showing Bind LED, Bind Button, and PPM port with its connections.

Binding Functionality

LED Indicator Behavior

The LED indicates active bind mode, successful binding, or binding failure.

Binding Procedure Steps

Instructions on how to properly install the transmitter module and enter bind mode.

Technical Specifications

FCC Compliance Statement

FCC Rules Compliance

Statement regarding compliance with Part 15 of FCC rules and potential interference.

User Modifications Warning

Warning that unauthorized modifications may void the user's authority to operate the equipment.

Declaration of Conformity

EU DoC Declaration

Declaration of compliance with RED 2014/53/EU and availability of the full text online.

RF Exposure Compliance

Antenna Installation Requirements

Antenna must provide a 20cm separation distance and not be co-located with other transmitters.

Environmental Disposal

Proper Disposal of Electrical Appliances

Guidance on separate disposal of old electrical appliances to recycle valuable materials.

Battery Replacement Caution

Caution regarding risk of explosion if battery is replaced by an incorrect type.

Overview

1. Function Description
2. Usage Features
3. Important Technical Specifications
4. Maintenance Features

The FS-RM003 is a 2.4G user manual for a transmitter module that utilizes a 2.4GHz frequency hopping digital transmission method to minimize external interference. This system incorporates binding for secure and reliable operation.

Function Description

The primary function of the FS-RM003 module is to enable wireless communication between a transmitter and a receiver, specifically for radio control applications. It employs a frequency hopping spread spectrum (FHSS) technique, known as AFHDS 2A (Automatic Frequency Hopping Digital System 2A), to enhance signal robustness and reduce the impact of interference. The module's binding process ensures a secure link between the transmitter and receiver, preventing unintended control by other radio systems.

Usage Features

• Binding Process: The device features a dedicated "Bind Button" and a "Bind LED" to facilitate the binding process. To enter bind mode, the user presses and holds the Bind button while the system is powered on. The Bind LED will flash to indicate that bind mode is active. Upon successful binding, the LED will stop flashing and remain solid. If the transmitter and receiver fail to bind, the LED will flash slowly. The LED will turn off after 10 seconds if binding is successful, indicating a completed process.
• PPM Port: The module includes a PPM (Pulse Position Modulation) port for signal input, along with GND (Ground) and VCC (Power) connections. This allows for integration with various transmitters that support PPM output.
• Installation: Before binding, it is crucial to ensure that the 2.4GHz transmitter module is correctly installed. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.
• Safety Precautions: The manual emphasizes several safety precautions for operation. Users should ensure the product is installed and working correctly before use. Operation is discouraged at night or during adverse weather conditions (rain, thunderstorms) due to the risk of erratic operation or loss of control. The product should not be used when visibility is limited or exposed to rain or snow, as moisture can lead to erratic operation or loss of control. To prevent interference and ensure safety, operation should be avoided near other radio control activity, people, roads, passenger boats on ponds/lakes, power lines, or communication broadcasting antennas.

Important Technical Specifications

• Frequency Range: 2.408-2.475GHz
• Bandwidth: 500KHz
• Number of Bands: 135
• Transmitter Power: ≤20dBm (for Europe)
• 2.4G Protocol: AFHDS 2A
• Antenna Length: 26mm
• Weight: 41g
• Input Power: 4.5-18V
• Size: 1785240mm
• Color: Black
• Certification: CE, FCC

Maintenance Features

• Environmental Disposal: The manual provides guidelines for environmentally friendly disposal of old electrical appliances. These appliances must not be disposed of with residual waste but must be disposed of separately at communal collecting points. The owner is responsible for bringing the appliances to these points to contribute to the recycling of valuable raw materials and the treatment of toxic substances.
• Battery Caution: A caution regarding batteries is included: "RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS." This highlights the importance of correct battery replacement and proper disposal of used batteries to prevent hazards.
• FCC Compliance: The device complies with Part 15 of the FCC Rules, ensuring that it does not cause harmful interference and accepts any interference received. Users are warned that changes or modifications not expressly approved by the responsible party could void their authority to operate the equipment. In case of interference, corrective measures such as reorienting/relocating the receiving antenna, increasing separation between equipment and receiver, connecting to a different circuit, or consulting a dealer/technician are recommended.
• DoC Declaration: Flysky Technology co., ltd declares that the Radio Equipment [FS-RM003] is in compliance with RED 2014/53/EU. The full text of the EU DoC is available online at www.flysky-cn.com.

Fly Sky FS-RM003 Specifications

General

Brand	Fly Sky
Model	FS-RM003
Category	Transmitter
Language	English