flyfly hobby DG-1000 User Manual

www.flyflyhobby. com
A
A'
CG
30mm
B
B'
small rubber band
Double-Side Tape
Cut away covering film.
Assemble left and right sides
the same way.
Must be purchased separately!
Cut off shaded portion.
Apply epoxy glue.
Drill holes with the specified
diameter (here: 2mm).
Pay close attention here!
Do not overlook this symbol!
Warning!
Apply instant glue
(CA glue, super glue).
Ensure smooth non-binding
movement while assembling.
2mm
A
B
L
R
C.A
Wing Span..........
Weight.................
Length.................
Wing Area...........
Wing Loading.....
Airfoil..................
Radio...................
2
2630mm(103")
1000g~1100g
1130mm(44.5")
28.5dm
33~35g/dm
HQ 3012
3 channel, 4servos
2
SPECIFICATIONS
Must be purchased
separately!
Must be purchased separately!
2.6 x 12mm TP screw
TP Screw
2.6 x 12mm
2.6 x 12mm TP screw
Linkage Stopper
3x4mm
2mm Nut
6 x 600mm Carbon pole
3 x 30mm Wire
2 turns:big rubber band
Must be purchased separately!
A =
A'
B =
B'
下面 Down side
A
B
A
B
L
R
A
B
A
B
3mm wood
3mm wood
A
B
Double-Side Tape
2.6 x 12mm TP screw
Must be purchased
separately!
C C'
C =
C'
1
2
3 x 18mm screw
2mm Nut
3 x 4mm
Linkage Stopper
Designed and Manufactured by :
FlyFly Hobby Mfg.
info@flyflyhobby.com
http://www.flyflyhobby.com
If the tail is not right angle
to the fin, apply tape to one
side to achieve the right
alignment.
Warning!
A
B
A
B
1 x90mm rod
Double-Side Tape
200mm
The CG position will vary
depends on your requirement.
Move the CG to achieve your
control style.
3
5
rubber band
2
1
6 x 600mm
Carbon rod
5
2
2
1
Horn
Linkage stopper
1 x 90mm wire
3mm plywood
Hook
13
TP Screw
2.6 x 12mm
3 x 18mm screw
with cover (cloth)
low setting
Use an iron covered with a cloth! Start
at low setting.Increase the setting if
necessary.If it is too high, you may
damage the film.
The pre-covered film on ARF kits
may wrinkle due to variations
of temperature.Smooth out as
explained below.
4
3 x 30mm
Wire
2
1 x 1000mm wire
飞飞
FLYFLY

flyfly hobby DG-1000 Specifications

General

Brand	flyfly hobby
Model	DG-1000
Category	Toy
Language	English

Summary

Before You Begin Assembly

Symmetrical Assembly and Movement

Assemble left and right sides identically and ensure smooth, non-binding movement.

Component Purchase Requirements

Highlights items that must be purchased separately for assembly.

Adhesive Application Guidance

Specifies the use of epoxy and instant glue for secure component attachment.

Drilling and Alignment Checks

Details drilling specifications and alignment procedures for critical parts.

Film Wrinkle Correction

Instructions on using an iron to smooth pre-covered film on ARF kits.

Critical Warning and Attention

Emphasizes important warnings and points requiring close attention during assembly.

Key Assembly Steps and Diagrams

Tail and Wing Alignment

Illustrates checking and achieving right angles for tail and wing assembly.

Radio and Control Surface Setup

Demonstrates the installation of radio components and linkage setup.

Center of Gravity (CG) Adjustment

Explains how CG position varies and how to adjust it for control style.

Component Attachment Details

Shows specific methods for attaching various parts using screws, tape, and rods.