What to do if surface burners will not operate on my Forza Ranges?
K
Karla TaylorAug 18, 2025
If the surface burners on your Forza range aren't working, several factors could be the cause. First, ensure the power supply cord is plugged into a grounded 3-prong outlet. Check if a household fuse has blown or the circuit breaker has been tripped, and replace the fuse or reset the circuit if necessary. If it's the first time using the surface burners, turn on any one of the surface burner knobs to release air from the gas lines. Also, make sure the control knob is set correctly by pushing it in before turning to a setting. Finally, inspect the burner ports for clogs; if clogged, consult the “Cleaning the burner cap and gas spreader” section for guidance.
M
Michael FernandezAug 20, 2025
Why is the oven temperature too hot or too cold in my Forza Ranges?
C
Curtis MorenoAug 21, 2025
If the oven temperature in your Forza range is too hot or too cold, the oven thermostat likely needs adjustment.
R
Ruben CrawfordAug 23, 2025
What to do if ignition will not operate on my Forza Ranges?
V
Victoria MooreAug 23, 2025
If the ignition on your Forza range isn't working, check a couple of things. First, make sure the power supply cord is plugged into a grounded 3-prong outlet. Also, see if a household fuse has blown or the circuit breaker has been tripped, and replace the fuse or reset the circuit if needed.
B
Brandi DillonAug 26, 2025
Why are the surface burners flames uneven yellow and/or noisy on my Forza Ranges?
J
John FletcherAug 26, 2025
Uneven, yellow, or noisy flames on your Forza range's surface burners can be due to several reasons. Check if the burner ports are clogged and refer to the “Cleaning gas burners” section. Ensure the burner caps are positioned properly; see the “Cleaning the burner cap and gas spreader” section. Finally, if propane gas is being used, the appliance may have been converted improperly, in which case you should contact a service technician.
J
Joseph SimsAug 28, 2025
What to do if oven light is not working properly in my Forza Ranges?
R
Robin RiceAug 28, 2025
If the oven light in your Forza range isn't working properly, try replacing or reinserting the light bulb if it's loose or defective.
E
Eddie JacksonAug 31, 2025
What to do if surface burners makes popping noise on my Forza Ranges?
K
Kenneth YoungAug 31, 2025
If the surface burners on your Forza range are making a popping noise, first check if the burner is wet and let it dry. Also, ensure the cap and gas spreader are positioned correctly, making sure the alignment pins are properly aligned; refer to the “Cleaning the burner cap and gas spreader” section.
D
David BergSep 2, 2025
How to prevent porcelain chips on Forza Ranges?
J
Johnathan MaddoxSep 2, 2025
To prevent porcelain chips on your Forza range, always tilt oven racks upward when removing and replacing them, and avoid forcing them.
C
Christopher GomezSep 4, 2025
What to do if there is excessive heat around cookware on cooktop of Forza Ranges?
N
normantroySep 5, 2025
If there is excessive heat around the cookware on your Forza range cooktop, make sure you are using cookware that is about the same size as the surface cooking area, element, or surface burner. Cookware should not extend more than 1 inch (2.5 cm) outside the cooking area.
A
Ashley AndersonSep 7, 2025
What to do if cooktop cooking result is not what expected on Forza Ranges?
P
poperobertSep 7, 2025
If your Forza range cooktop cooking results aren't what you expected, consult the “Cookware” section to ensure you're using the proper cookware. Also, refer to the “Setting the Control Knobs” section to verify the control knob is set to the proper heat level.
J
Justin GreerSep 9, 2025
How to remove lens cover on light of Forza Ranges?
M
Mario ValdezSep 9, 2025
If you cannot remove the lens cover on the light of your Forza range, wipe the lens cover area with a clean dry towel prior to attempting to remove it. There may be soil build-up around the lens cover.