EasyManua.ls Logo

FPZ SCL K09-TD - User Manual

Default Icon
49 pages
Go to English
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
COMPRESSORI - ASPIRATORI A CANALE LATERALE ‘SCL K-TD MOR’
ISTRUZIONI I
LATERAL CHANNEL BLOWERS - EXHAUSTERS ‘SCL K-TD MOR’
INSTRUCTIONS GB
COMPRESSEURS - ASPIRATEURS A CANAL LATERAL ‘SCL K-TD MOR’
INSTRUCTIONS F
SEITENKANALVERDICHTER - VAKUUMPUMPEN BAUREIHE ‘SCL K-TD MOR’
BETRIEBSANLEITUNG D
COMPRESORES - ASPIRADORES DE CANAL LATERAL ‘SCL K-TD MOR’
INSTRUCCIONES E
LEGGERE ATTENTAMENTE TUTTE LE ISTRUZIONI E CONSERVARLE I
PLEASE READ CAREFULLY ALL INSTRUCTIONS AND KEEP THEM FOR FUTURE REFERENCE GB
LIRE ATTENTIVEMENT TOUTES LES INSTRUCTIONS ET LES CONSERVER F
ALLE ANLEITUNGEN SIND SORGFÄLTIG ZU LESEN UND AUFZUBEWAHREN! D
SIRVASE LEER CUIDADOSAMENTE TODAS LAS INSTRUCCIONES Y CONSERVARLAS PARA FUTURA REFERENCIA E
SN 1977-0
®
F.P.Z. effepizeta s.r.l.
Via F.lli Cervi 16/18
20049 Concorezzo - (MI) - ITALIA
Tel. +39 039 604 1820
Fax +39 039 604 1296
www.fpz.com
SCL K07 / K08 / K09 / K10 / K11

Table of Contents

Questions and Answers

  • F
    fwalshAug 7, 2025
    What to do if my FPZ Blower unit does not start?
    • M
      mwatkinsAug 7, 2025
      If your FPZ Blower doesn't start, there are several potential causes: * Incorrect electric wiring: Check the electric wiring against the wiring diagram located in the terminal board box. * Unsuitable power supply voltage: Ensure that the power supply voltage, measured at the motor’s terminals, is within ± 5% of the nominal voltage. * Stuck impeller: In this case, it is best to get trained personnel to repair the machine.
  • H
    hernandezallisonAug 12, 2025
    Why does the power absorption of my FPZ SCL K09-TD Blower exceed the maximum allowed?
    • L
      littlemarkAug 13, 2025
      If the power absorption of your FPZ Blower exceeds the maximum allowed, consider the following: * Incorrect wiring: Verify the electric wiring against the wiring diagram in the terminal board box. * Voltage drop on the power supply: Restore the power supply voltage at the terminals to within the allowed values. * Clogged intake filter: Clean or replace the cartridge. * Deposits inside the unit: Have trained personnel clean the machine internally. * Operating beyond allowed pressure/vacuum: Adjust the plant and/or the regulating valve to reduce the pressure differentials.
  • J
    Jill ClarkAug 17, 2025
    How to reduce excessive noise from my FPZ SCL K09-TD Blower?
    • S
      Shirley PerezAug 17, 2025
      Excessive noise in your FPZ Blower can stem from several issues: * Damaged soundproofing fabric: Replace the soundproofing fabric. * Impeller scraping against the chassis due to: * Operating at excessive pressure/vacuum: Adjust the plant to reduce pressure differentials. * Internal deposits: Have trained personnel clean the machine internally. * Worn bearing: Replace the bearing. * Unsuitable installation position: Install the units on structures that cannot transmit or amplify the noise.
  • G
    garciakatrinaAug 22, 2025
    Why is the delivery air temperature high in my FPZ SCL K09-TD Blower?
    • G
      Gina HendersonAug 23, 2025
      High delivery air temperature in your FPZ Blower can be due to: * Operating at excessive pressure/vacuum: Adjust the plant and/or regulating valve to reduce pressure differentials. * Clogged intake filter: Clean or replace the cartridge. * Internal deposits: Have trained personnel clean the machine internally. * Clogged intake/delivery piping: Remove the obstructions. * High intake air temperature: Use a heat exchanger to reduce the air temperature at the intake if it exceeds 40°C.
  • K
    Kevin OneillAug 28, 2025
    What to do if the air flow rate is zero or insufficient in my FPZ SCL K09-TD Blower?
    • N
      Nicholas Martinez IIIAug 28, 2025
      If your FPZ Blower has zero or insufficient airflow, check the following: * Incorrect rotation direction: Ensure the direction of rotation matches the indication on the motor’s fan cowling. * Clogged intake filter: Clean or replace the cartridge.
  • B
    beckydavisSep 1, 2025
    Why is my FPZ SCL K09-TD Blower experiencing abnormal vibrations?
    • I
      isotoSep 1, 2025
      Abnormal vibrations in your FPZ Blower may be caused by: * Damaged impeller: Replace the impeller. * Deposits on the impeller: Get trained personnel to clean the machine internally. * Incorrect unit fixing: Fix the unit on anti-vibration supports.

Summary

General Instructions

Conditions of Use

Specifies operating environment and gas types for blowers/exhausters.

Storage and Shipping

Guidelines for storing and transporting the unit safely.

Installation

Instructions for proper mounting and connecting the blower/exhauster.

Electric Motor

Details on the electric motor, including power, voltage, and protection.

Installation Sketches

Pressure Service

Diagrams illustrating pressure service installation configurations.

Vacuum Service

Diagrams illustrating vacuum service installation configurations.

Parallel Pressure Service

Diagrams for parallel connection in pressure service.

Parallel Vacuum Service

Diagrams for parallel connection in vacuum service.

List Accessories

List of available accessories for installation.

Set Up Instructions

Start-Up with 90° Manifold

Procedure for starting the unit with a 90° manifold.

Start-Up Without 90° Manifold

Procedure for starting the unit without a 90° manifold.

Internal Cleaning Instructions

Cleaning Instructions

General procedure for cleaning the internal components of the blower.

Instruction for SCL K07-TD; K08-TD

Detailed procedure for cleaning SCL K07-TD and K08-TD models.

Instruction for SCL K09-TD; K10-TD; K11-TD

Replacement Sound-Absorbing Panels

Troubleshooting

FPZ SCL K09-TD Specifications

General IconGeneral
BrandFPZ
ModelSCL K09-TD
CategoryBlower
LanguageEnglish

Related product manuals