Need help?Do you have a question about the FreshPark QUARTER PIPE and is the answer not in the manual?
General| Category | Sports & Outdoors |
|---|---|
| Ramp Type | Quarter Pipe |
| Weight Capacity | 500 lbs |
| Color | Black |
| Features | Modular, Portable, Weatherproof |
| Width | 4 feet |
| Usage | Skateboarding, BMX, Inline Skating |
Align panels with hinges together and ensure edges are flush for proper assembly.
Bolt panels using 3" bolts, washers, and lock nuts, allowing free hinge movement.
Place and align the toe piece on the bottom panel's tubing, matching holes.
Secure the toe piece using 2" bolts, washers, and lock nuts to the bottom panel.
Align the top panel with the coping against the curved panel, angled away from the ramp.
Bolt the top panels together using 3" bolts, washers, and lock nuts.
Insert legs into receivers, matching the angle, and tighten with knobs.
Place and bolt support bars onto each leg of the quarter pipe.
Bolt short support bar to hinge using J-bolt, washer, and wing nut.
Bolt both support bars to leg using J-bolt, washer, and wing nut.
Align the two panels with hinges together and ensure edges are flush.
Bolt panels using 3" bolts, washers, and lock nuts, allowing free hinge movement.
Place the toe piece on the bottom panel with 3 hinges and align holes.
Secure the toe piece using 2" bolts, washers, and lock nuts.
Place the coping on the top panel and align its holes with the tubing holes.
Secure the coping using 2" bolts, washers, and lock nuts.
Insert legs into receivers, matching the ramp angle.
Tighten legs using knobs screwed into the receivers.
Align the two panels with hinges together and ensure edges are flush.
Bolt panels using 3" bolts, washers, and lock nuts, allowing free hinge movement.
Place coping on the flat side, aligning holes with panel tubing.
Attach coping using 2" bolts, washers, and lock nuts.
Insert desired height legs into the 4 funbox receivers.
Screw knobs into receivers to lock legs, then flip funbox onto legs.
Align ramps with hinges facing each other, ensuring sides are flush.
Bolt ramps together using J-bolts, washers, and wing nuts on hinges.
Align the 2 hinges on each side of the ramps, ensuring sides are flush.
Bolt ramps together using J-bolts, washers, and wing nuts on hinges.
Align the sides of the ramps, positioning tubes flush with each other.
Bolt ramps using big J-bolts on 4 tubes, washers, and wing nuts.
Align funbox hinges with quarter pipe hinges, ensuring sides are flush.
Bolt ramps using J-bolts, washers, and wing nuts on both hinges.
Insert legs into the back receivers of the funbox and tighten with knobs.
Align panels with hinges together, ensuring edges are flush.
Bolt panels using 3" bolts, washers, and lock nuts, allowing free hinge movement.
Place and align the toe piece on the flat side of the bottom panel.
Secure the toe piece using 2" bolts, washers, and lock nuts.
Place the coping on the flat side of the ramp and align holes with tubing.
Secure the coping using 2" bolts, washers, and lock nuts.
Bolt ramps together using J-bolts, washers, and wing nuts on hinges.
Place a long support bar on each side of the spine transfer, bolting to hinges.
Secure support bars with J-bolts, washers, and wing nuts, adjusting for fit.
Align two launch ramps facing each other, ensuring hinges and sides are flush.
Bolt ramps together using J-bolts, washers, and wing nuts on both hinges.
Align two funboxes by their 4 tubing holes together.
Bolt funboxes using J-bolts on each hole, with washers and wing nuts.
Align two funboxes by their 4 side tubes together.
Bolt funboxes using J-bolts on each tube, with washers and wing nuts.
To Next Page