11 PB
Model UPC
Cooling
Btu
Heating
Btu Volts
Cooling
Amps
Cooling
Watts
Heating
Amps
Heating
Watts EER CEER COP
Moisture
Removal-
Pints/HR CFM
Cooling Only
WCT08A10A
724587436655
8000 — 115
7.0
748 — — 10.7 10.6 — 1.8 250
WCT10A10A
724587436662
10000
— 115 9.3 935 — — 10.7 10.6 — 2.4 250
WCT12A10A
724587436952
12000 — 115
11.1 1250
— —
9.6 9.5
—
3.8 295
WCT12A10B
724587436952
11600 — 115
10.5 11700
— —
9.6 9.5
—
3.8 295
WCT10A30A
724587436945
10000 — 230
4.4 935
— —
10.7 10.6
—
2.7 275
WCT12A30A
724587436969
12000 — 230 5.4
1250
— —
9.6 9.5
—
3.8 300
WCT16A30A
724587436976
15400 — 230
7.5 1638
— — 9.4
9.3
— 4.8 290
Cooling with Heat Pump and Electric Heat
WHT12A33A
724587436983 11100
230 5.5
1181 1087 5.0
9.4
9.3 2.3 3.1
275
Cooling with Electric Heat
WET10A33A
724587436990
10000 11000 230 4.4
935
3550 16.0
10.7 10.6
—
2.7
260
WET12A33A
724587437003
12000
11000 230
5.4 1250
3550 16.0
9.6 9.5
—
3.8
290
WET16A33A
724587437010
15400 11000 230 7.5 1638
3550 16.0
9.4 9.3
—
4.8 290
SPECIFICATIONS
Figure 202 (Specications)
HEATING PERFORMANCE: Change-over from heat pump operation to resistance operation on models indicated is
automatic at a preset outside ambient temperature of approximately 35°F.
Calculate the heat loss of the space to be heated. As long as the heat loss does not exceed the resistance heating capacity
rating of the unit, the heating performance will be satisfactory.
Note: all models will produce condensate. If condensate disposal is desired, an optional drain kit is available.
DEFROST CONTROL: Initiated at 30°F (outdoor coil temperature) and terminated at 43°F (outdoor coil temperature).
During defrost, the compressor stops and the electric heat starts, then operates with the fan to maintain indoor comfort.
Below 43°F, the unit remains in electric heat mode.
DEFROST DRAIN: Drain automatically opens at approximately 50°F to prevent condensate from freezing inside drain pan.
Installation
Height W idth Depth
Height
of Front
Width of
Front
Depth
with
Front
Minimum
Extension Into
Room with
Front
15 ¾" 26 ½" 21" 17 ¼" 27 ½" 23 ¼" 7 ½"
Height W i d t h Depth
Depth
with
Front
Minimum
Extension
Outside
Thru-the-wall
Finished Hole
Height Width Max. Depth
16 ¾" 27" 16 ¾" 24 ¼"
9
/
16
" 17 ¼" 27 ¼" 15
5
/
16
"
Installation Clearances
Improper installation of the Air Condtioner can cause poor performance and premature wear of the unit.
Ensure that the Wallmaster unit is installed with proper clearances as described below.
Ensure no obstructions. or enclosures are within clearances limits to allow for proper airow.
Clearances
Rear of Unit - Three (3) feet
Figure 203 (Chassis Dimensions)
Figure 204 (WSE Sleeve Dimensions)
To Next Page
Loading...
Need help?
General
