Frient Entry Sensor Pro - IC Compliance Statement

To Next Page

To Previous Page

Sensor (a)

Magnet (b)

Sensor (a)

Magnet (b)

Sensor (a)

Magnet (b)

Sensor (a)

Magnet (b)

Sensor (a)

Magnet (b)

Sensor (a)

Magnet (b)

Sliding Door

Sensor (a)

Magnet (b)

Placement Examples - Doors

• Be sure to mount the sensor on the frame,

to protect the electronics from heavy vibra-

tions.

• The sensor and magnet should be

mounted on the side opposite from the

hinge/pivot point.

• Pay careful attention to the arrow printed on

the sensor. This should be oriented to face

the magnet. The distance between the two

should not exceed 5mm.

Placement Examples - Windows

• Be sure to mount the sensor on the frame,

to protect the electronics from heavy

vibrations.

• The sensor and magnet should be mounted

on the side opposite from the hinge/pivot

point.

• Alternatively, if the window slides open, the

sensor and magnet may be mounted in

many positions, however the sensor should

always be placed on the frame.

• Pay careful attention to the arrow printed on

the sensor. This should be oriented to face

the magnet. The distance between the two

should not exceed 5mm.

frient assumes no responsibility for any

errors, which may appear in this manual.

Furthermore, frient reserves the right to alter

the hardware, software, and/or specications

detailed herein at any time without notice,

and frient does not make any commitment

to update the information contained herein.

All the trademarks listed herein are owned by

their respective owners.

Distributed by frient A/S

Tangen 6

8200 Aarhus N

Denmark

www.frient.com

Other certications

• Zigbee Home Automation 1.2 certied.

CE certication

The CE mark axed to this product conrms

its compliance with the European Directives

which apply to the product and, in particular,

its compliance with the harmonized standards

and specications.

Frame

Window

Frame

Door

Window

Sensor (a)

Magnet (b)

Door

IN ACCORDANCE WITH THE DIRECTIVES

• Radio Equipment Directive (RED)

2014/53/EU

• RoHS Directive 2015/863/EU amending

2011/65/EU

IC statement

ISED statement

Innovation, Science and Economic

Development Canada ICES-003 Compliance

Label: CAN ICES-3 (B)/NMB-3(B).

ISED statement

Français

L’émetteur/récepteur exempt de licence

contenu dans le présent appareil est

conforme aux CNR d’Innovation, Sciences

et Développement économique Canada

applicables aux appareils radio exempts de

licence. L’exploitation est autorisée aux deux

conditions suivantes :

1. L’appareil ne doit pas produire de

brouillage;

2. L’appareil doit accepter tout brouillage

radioélectrique subi, même si le brouillage

est susceptible d’en compromettre le

fonctionnement.

English

This device contains licence-exempt

transmitter(s)/receiver(s) that comply

with Innovation, Science and Economic

Development Canada’s licence-exempt

RSS(s). Operation is subject to the following

two conditions:

1. This device may not cause interference.

2. This device must accept any interference,

including interference that may cause

undesired operation of the device.

This equipment complies with IC RSS-102

radiation exposure limits set forth for an

uncontrolled environment. This equipment

should be installed and operated with

minimum distance 20 cm between the

radiator and your body.

Cet équipement est conforme aux limites

d’exposition aux radiations IC CNR-102

établies pour un environnement non

contrôlé. Cet équipement doit être installé et

utilisé avec une distance minimale de 20 cm

entre le radiateur et votre corps.

FCC statement

Changes or modications to the equipment

not expressly approved by the party

responsible for compliance could void the

user’s authority to operate the equipment.

NOTE: This equipment has been tested and

found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide

reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses and can

radiate radio frequency energy and, if not

installed and used in accordance with the

instructions, may cause harmful interference

to radio communications. However, there is no

guarantee that interference will not occur in a

particular installation.

If this equipment does cause harmful

interference to radio or television reception,

which can be determined by turning the

equipment o and on, the user is encouraged

to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the

equipment and receiver.

• Connect the equipment into an outlet on

a circuit dierent from that to which the

receiver is connected.

• Consult the dealer or an experienced

radio/TV technician for help.

This device complies with FCC RF radiation

exposure limits set forth for an uncontrolled

environment. The antenna used for this

transmitter must be installed to provide a

separation distance of at least 20 cm from

all persons and must not be co-located

or operating in conjunction with any other

antenna or transmitter.

This device complies with part 15 of the FCC

Rules. Operation is subject to the following

two conditions:

1. This device may not cause harmful interfer-

ence, and

2. this device must accept any interference

received, including interference that may

cause undesired operation.