Care and Cleaning F.,_ To reduce risk of fire or serious injury to persons or property, comply with the
basic warnings listed in ImportantSafetylnstructions, pages 2-3, and those listed below
Clean lint screen after every load
* Beforecleaningthedryerinterior, unplugtheelectricalpowercordtoavoidelectrical
shock hazards
Do not use any type spray cleanser when cleaning dryer interior Hazardous fumes or
electrical shock could occur
Inside
Clean the lint screen after every Ioad_ Lint build-up in the screen restricts air flow, which
causes longer drying times. The screen is located at the bottom of the door opening
Remove by pulling straight up_ Remove the lint and replace the screen_
Occasionally a waxy build-up may form on the lint screen from using dryer-added fabric
softener sheets To remove this buildoup, wash the lint screen in warm, soapy water Dry
thoroughly and replace Do not operate the d0ter without the lint screen in place
Do not store or place laundry products
on top of dryer at any time They can
damage the finish or controls
If the dryer drum becomesstained from noncolorfast fabrics, clean the drum with a damp
cloth and a mild liquid household cleanser Remove cleanser residue before drying the
next load
Every 18 months an authorized servicer should clean the dryer cabinet interior and
exhaust duct, These areas can collect lint and dust over time_ An excessiveamount of
lint build-up could result in inefficient drying and possible fire hazard,
Outside
* Clean the cabinet with mild soap and water, Never use harsh, gritty or abrasive
cleansers,
If the cabinet becomes stained, clean with diluted chlorine bleach [1/2 cup
(120 ml) in 1 quart (95 liter) water]_ Rinse several times with clear water
• Remove glue residue from tape or labels with a mixture of warm water and mild
detergent Or, touch residue with the sticky side of the tape or label
Before moving the dryer, place a strip of cardboard or thin fiberboard under the front
leveling legs to prevent damage to floor.
Common Drying Problems
Many drying probbms involve poor cbaning results, poor soil and stain removal, residues of lint and scum, and fabric damagc,, For satisfactory drying results,
follow these suggestions provided by The Soap and Detergent Association.
P_OBLFM POSSIBLECAUSES SOLUTIONS
Greasy, oily * Fabric softener sheet, * Rub fabric soft_.,ner stains with bar soap,
stains Rinse and rewash
Lint
Pilling
(Fibers break olf,
ball up and cling
to fabric.)
Shrinking
Wrinkfing
* Overloading.
* Overdrying causes static
electricity.
* Lint screen not clean when
cycle began,
* Lint is attached to "pills."
* Reduce load size and rewash using liquid
fabric softener in the final rinse.
* Or, add a fabric softener sheet and tumble
without heat.
* Use lint brush or roller to remove lint,
PR=:VI:NTIVI:M EASURE$
* Add a f_,w bath tow_,ls to small loads for
proper tumbling.
* Some "silk-like" fabrics should be air dried.
* Use proper drying temperature,
* Place fabric softener sheet on top of load
before starting the dryer.
* Do not overload dryer.
* Use fabric softener in washer or dryer to
reduce static electricity.
* Remove items when they are slightly damp to
avoid overdrying.
* Check that lint screen is clean and in place.
* Pilling is normal with
synthetic arid permanent
press fabrics. This is due to
abrasion from normal wc,ar,
* Use a lint brush or shaver to remove pills,
* Use fabric softener to lubricate fibers,
* When ironir_g, use spray stard/ or fabric finish
on collars and cuffs
* Turn items inside out to reduce abrasion,
* Overdrying.
* Overloading.
* Leaving items in dryer after
cycle ends,
* Irreversible condition.
* Reduce load size and tumble at medium or
low heat for 5-10 minutes.
* Remove items immediately. Hang or fold.
4
* Follow fabric care label directions,
* If shrinking is a concern, check load often,
* Remove items while slightly damp and hang or
lay flat to complete drying.
* Block knits into shape
* Do not overload dryer.
* Remove items as soon as cycle ends,
To Next Page
Loading...
