To Next PageTo Next Page
Need help?Do you have a question about the Frigidaire Q4SE Series and is the answer not in the manual?
Safety markings indicate potential hazards. WARNING for injury/death, CAUTION for minor injury/damage.
Shut off power before maintenance. Failure may cause injury or death.
Disconnect all power before maintenance. Failure can cause injury or death.
Safety markings indicate potential hazards. Follow all safety information during installation, service, and operation.
Unit uses R-410A refrigerant. Using other refrigerants will damage the unit.
Disconnect all power before service. Failure to comply can result in personal injury or death.
Units are shipped fully charged with R-410A. Installation requires no charging if done correctly.
Do not place combustible materials, including gasoline, near the unit.
Wiring must comply with codes. Use correct conductors and circuit protection as per rating label.
Never operate without a filter. Install upstream of evaporator coil. Keep filters clean for efficiency.
Comply with local codes and National Electric Code (ANSI/NFPA 70) or Canadian Electrical Code.
Verify voltage, frequency, phase, supply adequacy, wiring label, factory wiring.
Use dedicated branch circuit. Install disconnect within sight. Provide overcurrent protection.
Unit cabinet must have uninterrupted electrical ground. Do not use gas piping. Ground via provided lug.
Module troubleshoots heat pump failures by monitoring compressor/thermostat data.
Module displays ALERT/TRIP LEDs. Count flashes for Flash Code to identify problem.
Explains LED meanings like 'POWER', 'ALERT', 'TRIP' and their troubleshooting correlation.
Q4SE requires 2-stage thermostat. 3-stage if electric heat is added. Connect low voltage wires.
Verify unit level, free from obstructions, sealed ductwork, proper wiring, grounded, thermostat settings.
Units are shipped fully charged with R-410A. Charging should only be done by qualified personnel.
Lists status LEDs, descriptions, and troubleshooting information for various fault codes.
Lists indications of miswired modules and recommended troubleshooting actions.
Specific steps to fix module issues like no power, intermittent power, trip LED, flash codes.
Safety markings indicate potential hazards. WARNING for injury/death, CAUTION for minor injury/damage.
Shut off power before maintenance. Failure may cause injury or death.
Disconnect all power before maintenance. Failure can cause injury or death.
Safety markings indicate potential hazards. Follow all safety information during installation, service, and operation.
Unit uses R-410A refrigerant. Using other refrigerants will damage the unit.
Disconnect all power before service. Failure to comply can result in personal injury or death.
Units are shipped fully charged with R-410A. Installation requires no charging if done correctly.
Do not place combustible materials, including gasoline, near the unit.
Wiring must comply with codes. Use correct conductors and circuit protection as per rating label.
Never operate without a filter. Install upstream of evaporator coil. Keep filters clean for efficiency.
Comply with local codes and National Electric Code (ANSI/NFPA 70) or Canadian Electrical Code.
Verify voltage, frequency, phase, supply adequacy, wiring label, factory wiring.
Use dedicated branch circuit. Install disconnect within sight. Provide overcurrent protection.
Unit cabinet must have uninterrupted electrical ground. Do not use gas piping. Ground via provided lug.
Module troubleshoots heat pump failures by monitoring compressor/thermostat data.
Module displays ALERT/TRIP LEDs. Count flashes for Flash Code to identify problem.
Explains LED meanings like 'POWER', 'ALERT', 'TRIP' and their troubleshooting correlation.
Q4SE requires 2-stage thermostat. 3-stage if electric heat is added. Connect low voltage wires.
Verify unit level, free from obstructions, sealed ductwork, proper wiring, grounded, thermostat settings.
Units are shipped fully charged with R-410A. Charging should only be done by qualified personnel.
Lists status LEDs, descriptions, and troubleshooting information for various fault codes.
Lists indications of miswired modules and recommended troubleshooting actions.
Specific steps to fix module issues like no power, intermittent power, trip LED, flash codes.
General| Brand | Frigidaire |
|---|---|
| Model | Q4SE Series |
| Category | Heat Pump |
| Language | English |
