Fronius TTG 1200 - User Manual

Questions and Answers

E
Erika PerezAug 12, 2025
What to do if there is no welding current in Fronius Welding Accessories?
- I
  Isaiah BonillaAug 12, 2025
  If you're experiencing no welding current with your Fronius Welding Accessories, there are several potential causes. First, check the earth (ground) connection and clamp to ensure they have the correct polarity. Second, inspect the current cable in the welding torch for any breaks and replace the torch if necessary. Also, make sure the tungsten electrode is tightened using the torch cap. Finally, check for any loose parts and tighten them.
D
David SuarezAug 16, 2025
What to do if Fronius Welding Accessories machine does not function when the torch trigger is pressed?
- K
  Kevin ReynoldsAug 16, 2025
  If your Fronius welding machine doesn't function when you press the torch trigger, start by ensuring the control plug is properly connected. If it is, the welding torch or torch control lead might be defective; try exchanging them. Also, check if the welding torch connection socket is expanded and bend the contacts on the torch connecting plug accordingly. Inspect all plug connections between the torch trigger, control lead, and power source, and clean out any dirt between the trigger button and the button housing. As a last resort, the PCB in the welding torch might be defective, and you will need to replace it.
Z
zdavisAug 20, 2025
Why is there high frequency arc-over on the handle shell of Fronius Welding Accessories?
- A
  Angela LyonsAug 20, 2025
  If you're getting high-frequency arc-over on the handle shell of your Fronius Welding Accessories, it's likely due to a leaking hosepack. In this case, you should replace the hosepack. Alternatively, the shielding gas hose connection to the torch body might be leaking, requiring you to cut back the hose and reseal it.
J
James EdwardsAug 23, 2025
Why are Fronius Welding Accessories giving poor welding properties?
- S
  Samantha BlakeAug 23, 2025
  If you're experiencing poor welding properties with your Fronius Welding Accessories, first check your welding parameters to ensure they are set correctly. Also, verify that there is a good connection to earth (ground) to the workpiece.
M
Michael LewisAug 27, 2025
What to do if there is no shielding gas in Fronius Welding Accessories?
- J
  James WilsonAug 27, 2025
  If you have no shielding gas with your Fronius Welding Accessories, first, check if the gas cylinder is empty and change it if needed. If the cylinder isn't the problem, the gas pressure regulator might be faulty, requiring replacement. Also, inspect the gas hose to ensure it is properly mounted, not damaged, and not kinked; mount, straighten, or exchange it as necessary. The welding torch itself could be faulty, so try exchanging it. Finally, the gas solenoid valve might be faulty, and you should exchange it.
J
Jose HoodAug 30, 2025
What to do if there is high frequency arc-over on torch connection of Fronius Welding Accessories?
- T
  Tyler GardnerAug 31, 2025
  If you're experiencing high-frequency arc-over on the torch connection of your Fronius Welding Accessories, the welding torch connection is likely leaking. Replace the O-ring on the bayonet fixing to resolve this issue.
M
marcus98Sep 3, 2025
Why is the Fronius Welding Accessories torch becoming very hot?
- A
  Ashley ReyesSep 3, 2025
  If your Fronius welding torch becomes very hot, it might be because the torch's design dimensions aren't sufficient for the task. Make sure to respect the duty cycle and loading limits. Also, particularly on water-cooled machines, insufficient water through-flow could be the issue. Check the coolant level, through-flow rate, coolant cleanliness, and hosepack arrangement. If the coolant pump is blocked, use a screwdriver on the bushing to turn the shaft of the coolant pump.
T
thomas37Sep 8, 2025
How to fix Fronius Welding Accessories when welding torch cannot be connected?
- A
  Amy SheltonSep 8, 2025
  If the welding torch cannot be connected to your Fronius Welding Accessories, it is possible that the bayonet fixing is bent. If this is the case, you will need to replace the bayonet fixing.