What to do if my Full Vision Treadmill will not start?
If your Full Vision Treadmill won't start, ensure the safety lanyard clip is connected to the switch. Also, check the J12 connector on the lower smart power supply board and the J8 connector on the upper LCD circuit board located in the control console.
How to troubleshoot Full Vision Treadmill control console that will not illuminate?
To troubleshoot a Full Vision Treadmill control console that won't illuminate: First, turn the treadmill main power switch to OFF, and unplug the treadmill from the wall receptacle. Verify the J12 connector on the lower smart power supply board, and the J8 connector on the upper LCD circuit board located in the Control Console. Also, verify the J4 & J5 jumper is connected; it is located to the right side of the large transformer. Check the continuity of each conductor of the power cord and the function of the main power switch in the ON and OFF positions.
Identifies the target audience and their expected knowledge for operating the treadmill.
Defines the medical applications and environments for which the treadmill is designed.
Lists conditions or situations where using the treadmill is not advised.
Provides essential details on safe use, regulatory compliance, and manufacturer responsibilities.
Details the procedure for reporting any serious incidents related to the device.
Explains symbols (NOTE, CAUTION, WARNING) and lists general safety hazards.
Covers medical device classification and responsibilities of manufacturer and customer.
Explains device symbols, serial decal information, and training recommendations.
Defines the reference points (front, rear, left, right) for treadmill components.
Lists the various safety features integrated into the treadmill's design.
Provides key details on weight capacity, construction, and net weight.
Describes the motor type, power, and supply requirements for the drive system.
Details the adjustable speed and incline capabilities of the treadmill.
Describes the dimensions, belt tracking, deck cushioning, and step-up height.
Identifies the available ports for connecting external devices.
Specifies the dimensions required for treadmill placement.
Lists recommended temperature, humidity, and altitude ranges for operation and storage.
Details the electrical supply needs and available plug types for the treadmill.
Provides critical instructions for performing Hi-Pot tests safely and correctly.
Step-by-step guide for safely removing the treadmill from its packaging.
Guides the user through the initial assembly and placement of the treadmill.
Details the assembly process for the treadmill's control console.
Provides crucial advice for safely moving and positioning the treadmill.
Specifies minimum clearances and surface requirements for treadmill placement.
Covers adjustments for belt tracking, belt tension, and drive belt tension.
Instructions for using the RS-232 test plug to verify treadmill functionality.
Identifies the location of RS232 and USB ports and driver software information.
Outlines required electrical safety tests to be performed before use.
Details power switch, emergency stop, pull tether, and their operation.
Guides use of TMX428CP console, display info, and stop tether.
Covers workout graphics, manual operation, built-in programs, and user-defined workouts.
Emphasizes the importance of regular maintenance for treadmill longevity and performance.
Provides steps for cleaning and disinfecting the treadmill between patient uses.
Lists essential daily checks and cleaning procedures for the treadmill.
Details weekly tasks including vacuuming, belt tension, and tracking checks.
Specifies monthly tasks, primarily focused on belt cleaning and inspection.
Outlines semiannual tasks like deck evaluation, belt adjustments, and lubrication.
Provides detailed steps for cleaning the running belt and inspecting for damage.
Guides on adjusting running belt tracking and tension for optimal performance.
Explains how to adjust the drive belt tension to prevent looseness and noise.
Offers guidance on cleaning the treadmill's powder-coat finish.
Details the procedure and frequency for lubricating the elevation screw.
Describes maintenance for the running deck, including flipping for wear.
Lists parts and diagrams for the motor mount assembly.
Details components and diagrams for the circuit board assembly.
Lists parts and diagrams for the elevation assembly.
Details components and diagrams for the pull tether and emergency stop assemblies.
Provides a diagram and part list for the motor pan assembly.
Illustrates the wiring connections within the motor pan assembly.
Lists parts and diagrams for the treadmill frame assembly.
Details components and diagrams for the deck assembly.
Guides on final assembly procedures and circuit board connections.
Provides steps to diagnose and resolve issues where the control console does not light up.
Addresses problems with facility circuit breakers tripping when the treadmill powers up.
Guides on diagnosing why the treadmill fails to start, checking connections and tether.
Covers common running belt problems like slippage and being off-center.
Explains where to find and how to reset internal circuit breakers.
Provides comprehensive guidelines for cleaning and disinfecting the treadmill.
Detailed steps for manually cleaning the treadmill surfaces with approved solutions.
Outlines the steps for disinfecting the treadmill using isopropyl alcohol.
Details drying the device and visually inspecting for cleanliness after cleaning.
General| Brand | Full Vision |
|---|---|
| Model | TRACK MASTER TMX428 |
| Category | Treadmill |
| Language | English |
To Next Page