Fusion ACTIVE TUBE CS-AT1100 User Manual

ACTIVE TUBE
SPECIFICATIONS
 CS-AT1100
PeakPower(Watts) 360
RatedPower(Watts) 120
FrequencyResponse 36Hz-250Hz
LowPassFilter(Variable) 40Hz-250Hz
Tuning BassReex
WooferSize 10”
Fuse 20A
Dimensions(mm) 559(l)x306(w)x306(h)
 22-1/32x12-1/16x12-1/16”
CS-AT1100
www.fusionelectronics.com
CONTROL DESCRIPTIONS
LEVEL
Thisallowstheadjustmentoftheamplierlevelofthesubwoofer.
Turnclockwisetoincreasethelevel.Ifthesoundbecomesdistorted
reducethelevel.
LOW PASS FILTER (LPF)
This allows the adjustment of the highest frequency the Active
Tubewillproduce.Thisshouldbeadjustedtoblendwithyourmain
speakers.Typically,thiswillbesettoaround100Hz(approximately
thecentralpositionofthecontrolknob).
REMOTE LEVEL CONTROLLER
Whenconnected,thisallowsfurthercontroloverthelevelfroma
remotelocation,usingthesuppliedlead.
INSTALLATION
Makesure the Active Tube is rmlyxedin your vehicle. Check
beforedrillingorcuttingholes.DONOTworkneargastanks,fuel
lines,hydrauliclinesorelectricalwiring.
DONOTmounttheActiveTubeinsuchawayastopinchordamage
thewires.
Make sure everything is rmly connected, before attaching the
+12Vwire.Ensurethe+12Vwireisfusedascloseaspossibletothe
battery.Alwaysuseafusewiththerecommendedrating.
DISCLAIMER
AlwaysensuretheActiveTubeissecurelyattached,toavoidmovement.FUSIONacceptsnoresponsibilityfordamageorinjuryinrelation
toinappropriatesecuringofthisproduct.
WIRING
• Connectthegroundwiretothevehiclerst(cleandirtandpaint
 tobaremetal).
• Connecttheremoteon(bluewire).
• ConnecttheRCAcablesifapplicable,OR
• Connectthespeakerlevelwirebysplicingintotheheadunits 
 speakerwires.SeeNote1onreverse.
• Connecttheremotelevelcontrollerwiththesuppliedlead.
• Connectthe12volt(redwire)tothepositivebatteryterminal.
• Checkallconnections.

Fusion ACTIVE TUBE CS-AT1100 Specifications

General

Brand	Fusion
Model	ACTIVE TUBE CS-AT1100
Category	Subwoofer
Language	English

Summary

Product Specifications

Peak Power Output

Peak power output of the subwoofer in Watts.

Rated Power Output

Continuous power output of the subwoofer in Watts.

Frequency Response Range

Range of frequencies the subwoofer can reproduce.

Variable Low Pass Filter

Adjustable filter to set the highest frequency the subwoofer will produce.

Tuning Type

The acoustic design type of the subwoofer enclosure.

Woofer Diameter

Diameter of the speaker cone in inches.

Fuse Rating

The rating of the protective fuse in Amperes.

Product Dimensions

Physical size of the subwoofer in millimeters and inches.

Control Descriptions

Level Adjustment

Adjusts the amplifier level of the subwoofer for desired volume.

Low Pass Filter (LPF) Adjustment

Sets the highest frequency the Active Tube will produce to blend with main speakers.

Remote Level Controller Function

Allows remote adjustment of the subwoofer's level via a supplied lead.

Installation and Wiring Instructions

Installation Precautions

Ensures secure mounting, avoids damage to wires, and proper fuse usage during installation.

Wiring Connections Guide

Details connecting ground, remote, RCA/speaker level, and power wires for proper function.

Important Notes and Warnings

Speaker Phase Connection Importance

Correctly splicing speaker wires prevents loss of bass.

Hearing Safety Warning

Warns about high sound pressure levels causing permanent hearing loss.