Fusion CA-AM41200 User Manual

AMPLIFIERS
AMPLIFIER SPECIFICATIONS
 CA-AM10900 CA-AM20350 CA-AM20650 CA-AM40700 CA-AM41200
PeakPower(Watts) 900 350 650 700 1200
FrequencyResponse 15Hz-185Hz 10Hz-100kHz 10Hz-100kHz 10Hz-100kHz 10Hz-100kHz
Dimensions(mm) 267(l)x230(w)x49(h) 267(l)x230(w)x49(h) 377(l)x230(w)x49(h) 377(l)x230(w)x49(h) 457(l)x230(w)x49(h)
 10-1/2x9-1/16x1-15/16” 10-1/2x9-1/16x1-15/16” 14-27/32x9-1/16x1-15/16” 14-27/32x9-1/16x1-15/16”18x9-1/16x1-15/16”
PowerRatings 300WRMSx1 55WRMSx2 115WRMSx2 50WRMSx4 110WRMSx4
 @4Ω1%THD+N, @4Ω1%THD+N, @4Ω1%THD+N, @4Ω1%THD+N, @4Ω1%THD+N,
 480WRMSx1 85WRMSx2 170WRMSx2 80WRMSx4 150WRMSx4
 @2Ω1%THD+N @2Ω1%THD+N, @2Ω1%THD+N, @2Ω1%THD+N, @2Ω1%THD+N,
  175WRMSx1 340WRMSx1 160WRMSx2 300WRMSx2
  @4ΩBridged @4ΩBridged @4ΩBridged @4ΩBridged
  1%THD+N 1%THD+N 1%THD+N 1%THD+N
CA-AM10900 CA-AM20350 CA-AM20650 CA-AM40700 CA-AM41200
www.fusionelectronics.com
INSTALLATION GUIDELINES
1. Ensurethe+12Vleadisdisconnectedfromthebatterybeforeyouconnectanynewequipment.
2. Ensurethemountinglocationwillnotinterferewiththegastank,brakelinesorelectricalwiring.
3. EnsuretheAmplierissecurelyfastenedtothevehicletopreventdamageintheeventofanaccident.
4. Ensureallwiringisprotectedtoavoidpinchingorcrushingwhichcouldresultindamagetotheaudiosystem.
5. Ensurethemountinglocationhassufcientairowaroundtheamplier.Iftheamplierismountedinanenclosedspacea
 3”fanwithductingshouldbeusedtoaidinairow.
6. Donotmountanyamplieronasubwooferenclosureasextendedexposuretovibrationmaycausemalfunctionoftheamplier.
7. Ensureyouusetherecommendedgaugewire/cableforallamplierconnections.
WIRING
Ensuretheaudiosystemisturnedoffbeforemakinganyconnections
totheamplier,speakersorsourceunit.
Failuretodo so could resultin permanent damage tothe audio
system.WhenwiringtheFUSIONamplierensurethatthecable
isprotectedfromsharpobjectsandalwaysuserubbergrommets
whenwiringthroughmetalpanels.
Ensure all terminals and connections are protected from the
vehiclechassisandfromeachotherasfailuretodosocouldresult
inpermanentdamagetotheaudiosystem.
POWER
FUSIONampliersshouldbeconnecteddirectlytothe+12Vbattery
terminalwithaninlinefuseorcircuitbreakerasclosetothebattery
aspossible.
GROUND
Whengrounding/earthingyouramplier ensurethat the location
isagoodsourceof ground(preferablythe oor pan). Makesure
themetaliscleanofpaintetcasapoorearthcoulddamageyour
audiosystem.
REMOTE TURN ON
Thisconnectionturnstheamplieronandshouldbeconnectedto
theremoteturnonwirefromtheHeadUnit.Ifoneisnotavailable
aswitched12vsourcemustbeused.Eitherapowerantennawire
orACC+12V.
LOW LEVEL INPUTS
ChoosethecorrectlengthRCAinterconnectsandrunthemtothe
RCAoutputsofthesource/headunit,avoidingrunningbesideother
loomsandorpowercable.
LEVEL CONTROL
Thiscontrolisusedtomatchtheinputleveloftheampliertothe
outputlevelofyouheadunit.Werecommendthefollowingmethod.
1. Turntheamplierleveltozero
2. Turnthevolumeoftheheadunitto¾andthebassandtreble
 tozero
3. Adjustthelevelcontroluntilthedesiredmaximumvolumeis
 achievedwithoutdistortion.
4. Failuretofollowthesestepsmaycausepermanentdamageto
 theaudiosystem.

Fusion CA-AM41200 Specifications

General

Brand	Fusion
Model	CA-AM41200
Category	Car Amplifier
Language	English

Summary

Amplifier Installation and Operation

Installation Guidelines

General recommendations for safely and correctly installing the amplifier in a vehicle.

Wiring Procedures

Instructions for connecting the amplifier to the vehicle's audio system and power source.

Power and Ground Connections

Guidance on proper +12V battery terminal connection and secure grounding.

Remote Turn-On and Input Signals

Details on connecting the remote turn-on wire and low-level RCA inputs.

Level Control Adjustment

Procedure for matching the amplifier's input level to the head unit's output.

Amplifier Installation Kits and Crossover Settings

Recommended Installation Kits

Specific FUSION amplifier installation kits recommended for each amplifier model.

Crossover Type and Frequency

Information on selectable crossover types (LPF, HPF, FULL) and frequencies for each model.

Troubleshooting Amplifier Issues

Amplifier Not Switching On

Diagnosing and resolving issues when the amplifier's power LED is off.

No Sound from Amplifier

Troubleshooting steps for when the amplifier is powered but no audio is produced.