FUTABA R7114SB Quick Start Guide

R7114SB

 
◆
FASSTest-2.4GHz Bidirectional Communication System / FASST-Multi-ch 2.4GHz
◆
S.BUS2 / S.BUS Port and 12 Channels (+DG1,2) for Conventional System Receiver
◆
with High gain antenna
1M23N36202

• Analog servos cannot be used with the R7114SB in the FASSTest
12CH mode.
• When the FASST Multi-ch High-speed Mode is used, analog servos
cannot be used at the CH1
〜
6 outputs for convention systems. How-
ever, in other than the FASSTest 12CH mode, analog servos can be
used at CH7
-
12, DG1 and DG2 at any time.
• Don't connect to Extra Voltage Telemetry Port before turning on a re-
ceiver.

Changesormodificationnotexpresslyapprovedbytheparty
responsibleforcompliancecouldvoidtheuserʼ sauthoritytooperatethe
equipment.
TheR7114SBreceivershouldbeprotectedfromvibrationbyfoam
rubber,Velcro,orsimilarmountingmethods.Protectfrommoisture.

Donotcutorbundlethereceiverantennawire.
Donotbendthecoaxialcable.Itcausesdamage.
Theantennasmustbemountedinsuchawaytoassuretheyarestrain
relieved.
Keeptheantennaasfarawayfromthemotor,ESCandothernoise
sourcesasyoupossiblycan.
Besurethatthetwoantennasareplacedat90degreestoeachother.
■ The R7114SB has two antennas. In order to maximize signal reception and
promote safe modeling Futaba has adopted a diversity antenna system. This allows
the receiver to obtain RF signals on both antennas and fly problem-free.

Youmustleave30mmatthetipoftheantennafullyexposed.The
exposedantennashouldbesecuredsothatitcannotmovearoundor
backinsideofyouraircraft.

Don'tconnectanS.BUSservo/gyrotoS.BUS2connector.
Donotconnectthepowersupplybatterytootherthanthepower
supplyconnector.
■ There is the danger of ignition, explosion, or burning.

Donotperformthelinkingprocedurewhilethemotor'smainpoweris
connectedortheengineisoperatingasitmayresultinseriousinjury.
Whenthelinkingiscomplete,pleasecyclethereceiverpowerand
ensurethereceiverisproperlylinkedtothetransmitter.
Pleasepowerupyoursysteminthisorder.Transmitterfirst,followed
bythereceiver.
IftheR7114SBreceiverwaspreviouslylinkedtoanothertransmitter,
makesurethattransmitterisnotoperatingwhilelinkingthereceiverto
thenewtransmitter.
56%
/LQN0RGH
VZLWFK
$QWHQQD
0RGH/('
/LQN/('
([WUD9ROWDJH
7HOHPHWU\3RUW
Thank you for purchasing a Futaba R7114SB FASSTest-2.4GHz compatible receiver. The R7114SB receiver features bi-directional communication with a FASSTest
Futaba transmitter using the S.BUS2 port. Using the S.BUS2 port an impressive array of telemetry sensors may be utilized. It also includes both standard PWM output
ports and S.BUS output ports. The R7114SB can also be switched to the FASST-Multi-ch System.

FASSTest-2.4GHz system(14ch/12ch mode)
FASST-2.4GHz system (Multi-ch mode)
S.BUS2 and S.BUS port and Linear 12ch +Digital 2ch for conventional
system receiver
• Dual antenna diversity
• Size: 1.98 x 1.45 x 0.63 in. (50.2x37.0x15.9 mm)
• Weight: 0.77 oz. (21.9 g)
• Power requirement: 3.7 V to 7.4 V (Voltage range: 3.5 V to 8.4 V)
• Battery F/S Voltage: FASSTest:It sets up with a transmitter
FASST: 3.8 V *The Battery F/S voltage is set for 4-cell NiCd/NiMH bat-
tery. Battery F/S function doesn't work properly when other type battery
is used.
• Extra Voltage port: 0 V-70 V DC
&+6HUYRV
'HIDXOW6%86SRUW
,WVSRVVLEOHWRFKDQJHWR'*
6%86
6%86
'*
'*

FKDQQHO
+XE
6%86HTXLSPHQW
7HOHPHWU\VHQVRU
7HOHPHWU\VHQVRU
7KHUHFHLYHUSRZHUVXSSO\FDQ
EHFRQQHFWHGWRDQ\SRUW
%DWWHU\
ۋ9
6ZLWFK
6HUYR
<KDUQHVV
:KHQDOOSRUWVDUHXVHG



The direction of the
connectors of the
bottom 3 ports is
GLIIHUHQWE\Û

   



 
 

   

 󱐯
 
 
 
 





90°
Antenna
installation
Donotbendtheantennapart
Gentlybendthecoaxial
cablepart.
Fixthesleevetothemodel
$QWHQQDSDUW
6OHHYH
&RD[LDOFDEOH

Hereby, Futaba Corporation declares that the radio equipment type is R7114SB in compliance with Directive 2014/53/
EU. The full text of the EU declaration of conformity is available at the following internet address:
http://www.rc.futaba.co.jp/english/dl/declarations.html

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device. This equipment complies with IC radiation exposure
limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum dis
-
tance 20cm between the radiator & your body.
French: Cet appareil radio est conforme au CNR-210 d’Industrie Canada. L’utilisation de ce dispositifest autorisée
seulement aux deux conditions suivantes : (1) il ne doit pas produire de brouillage, et (2) l’utilisateur du dispositif doit
être prêt à accepter tout brouillage radioélectrique reçu, même sice brouillage est susceptible de compromettre le fonc
-
tionnement du dispositif. Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un
environnement non contrôlé.
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non
contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de ray
-
onnement et votre corps.

This device, trade name Futaba Corporation, model number R7114SB, complies with part15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
CAUTION: To assure continued FCC compliance
$Q\FKDQJHVRUPRGL¿FDWLRQVQRWH[SUHVVO\DSSURYHGE\WKHJUDQWHHRIWKLVGHYLFHFRXOGYRLGWKHXVHUVDXWKRULW\
to operate the equipment.
2. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
The responsible party of this device compliance is:
FUTABA Corporation of America
2681 Wall Triana Hwy Huntsville, AL 35824, U.S.A.
Phone:1-256-461-9399 FAX:1-256-461-1059 E-mail: service@futabaUSA.com
低功率射頻器材技術規範 3.8.2 警語
取得審驗證明之低功率射頻器材，非經核准，公司、商號或使用者均不得擅自變更頻率、加大功率或變更
原設計之特性及功能。
低功率射頻器材之使用不得影響飛航安全及干擾合法通信 ；經發現有干擾現象時，應立即停用，並改善至
無干擾時方得繼續使用。
前述合法通信，指依電信管理法規定作業之無線電通信。低功率射頻器材須忍受合法通信或工業、科學及
醫療用電波輻射性電機設備之干擾。
%DVHG XSRQ WKH SURGXFW VSHFL¿FDWLRQ SURYLGHG E\ WKH PDQXIDFWXUHUWKLVHTXLSPHQWLVHYDOXDWHGWREH
supplied by an approved external power supply source suitable for use at minimum Tma 40°C whose
output meets LPS(or PS2), SELV(or ES1) and output is rated: 3.7Vdc to 7.4Vdc.

FUTABA R7114SB Specifications

General

Brand	FUTABA
Model	R7114SB
Category	Conference System
Language	English