Galaxy Audio PA6BT User Manual

GAL A X Y AUDIO Quick Start Guide
PA6BT
Full Range Powered Personal Monitor
Included Components
1. PA6BT x1
3. MSA-1 Stand Adapter x1
2. IEC Power Cable x1
Setup
2.1.
4.
4. Quick Start Guide x1
3.
Connect power cable to PA6BT, connect
other end to a power outlet.
2
Choose the input needed and for what
channel(s) needed:
XLR/1/4" Combo Jack for mic, or
balanced/unbalanced line level.
1/8" for stereo from a media player etc.
3
For a balanced mic signal, plug the XLR
male end of the cable into the XLR/1/4"
Combo Input on the PA6BT. For strong
signals, engage the -20dB Pad Switch to
prevent distortion.
4
For Balanced or Unbalanced Line Level,
plug the 1/4" cable into the XLR/1/4"
Combo Jack on the PA6BT.
5
Connect a female XLR to the Thru
output to feed the channel’s XLR input
to another device.
1
For a stereo signal from an MP3 player,
attach 1/8" stereo cable into the Channel
2 1/8" input.
6
Flip the power switch on.
3
Level controls: turn clockwise to raise the
level. Turn counter-clockwise to lower
the level.
4 5 62
EQ controls - Low/Mid/Hi: To increase the
low, mid, and high frequencies, turn the
appropriate tone control clockwise. To
decrease, turn counter-clockwise.
1
Ensure that both channels and/or the
Bluetooth controls have their levels ®
lowered by turning counter-clockwise.
Stand Mounting (Optional)
1
Attach the MSA-1 to the mic stand, then
Lift the PA6BT over the stand, align it up
with the hole.
2
Bring the PA6BT down onto the stand
gently until secure.
Operation
The Pre Out provides a Line Level mix
of all three channels.
7
Reduce Input Levels if the Clip LED turns
on. Max. level is reached when the yellow
“Comp” light flashes at peak levels. If the
light is on constantly, turn the levels down
to avoid damage to
the PA6BT.
Using Bluetooth - Press the Bluetooth® ®
button. The Bluetooth LED will flash for®
15 seconds. Locate the PA6BT on your
device and select to pair. If pairing fails,
turn Bluetooth off and try again. The®
button also acts as a Stop/Play/Pause.
Powering the unit off will disconnect.
GAL AX Y AUDIO Quick Start Guide
PA6BT
Full Range Powered Personal Monitor
Included Components
1. PA6BT x1
3. MSA-1 Stand Adapter x1
2. IEC Power Cable x1
Setup
2.1.
4.
4. Quick Start Guide x1
3.
Connect power cable to PA6BT, connect
other end to a power outlet.
2
Choose the input needed and for what
channel(s) needed:
XLR/1/4" Combo Jack for mic, or
balanced/unbalanced line level.
1/8" for stereo from a media player etc.
3
For a balanced mic signal, plug the XLR
male end of the cable into the XLR/1/4"
Combo Input on the PA6BT. For strong
signals, engage the -20dB Pad Switch to
prevent distortion.
4
For Balanced or Unbalanced Line Level,
plug the 1/4" cable into the XLR/1/4"
Combo Jack on the PA6BT.
5
Connect a female XLR to the Thru
output to feed the channel’s XLR input
to another device.
1
For a stereo signal from an MP3 player,
attach 1/8" stereo cable into the Channel
2 1/8" input.
6
Flip the power switch on.
3
Level controls: turn clockwise to raise the
level. Turn counter-clockwise to lower
the level.
4 5 62
EQ controls - Low/Mid/Hi: To increase the
low, mid, and high frequencies, turn the
appropriate tone control clockwise. To
decrease, turn counter-clockwise.
1
Ensure that both channels and/or the
Bluetooth controls have their levels ®
lowered by turning counter-clockwise.
Stand Mounting (Optional)
1
Attach the MSA-1 to the mic stand, then
Lift the PA6BT over the stand, align it up
with the hole.
2
Bring the PA6BT down onto the stand
gently until secure.
Operation
The Pre Out provides a Line Level mix
of all three channels.
7
Reduce Input Levels if the Clip LED turns
on. Max. level is reached when the yellow
“Comp” light flashes at peak levels. If the
light is on constantly, turn the levels down
to avoid damage to
the PA6BT.
Using Bluetooth - Press the Bluetooth® ®
button. The Bluetooth LED will flash for®
15 seconds. Locate the PA6BT on your
device and select to pair. If pairing fails,
turn Bluetooth off and try again. The®
button also acts as a Stop/Play/Pause.
Powering the unit off will disconnect.

Galaxy Audio PA6BT Specifications

General

Type	Portable PA System
Bluetooth	Yes
Bluetooth Version	4.0
Inputs	1 x 1/8" (aux), XLR, 1/4"
Speaker Size	1" Tweeter
Bluetooth Range	30 feet

Summary

GALAXY AUDIO PA6BT Personal Monitor Setup

Connecting Power and Audio Inputs

Connect the power cable and various audio sources like microphones and line-level devices to the PA6BT.

Utilizing the Thru Output

Route the XLR input signal to another device via the Thru output for signal chaining.

Secure Stand Mounting

Instructions for attaching the PA6BT to a microphone stand using the included adapter.

Operating Controls and Features

Learn to power on, adjust levels, use Bluetooth, manage EQ, and monitor input signals.

PA6BT Frequently Asked Questions

Wall Mounting and Bracket Compatibility

Information on how to mount the PA6BT to a wall using optional bracket kits.

Thru Output Functionality

Clarification that the Thru output is exclusively for XLR input signals.

Condenser Microphone Support

Confirmation of compatibility with condenser microphones due to 15VDC Phantom Power.

Bluetooth Device Reconnection

Details on automatic Bluetooth reconnection after powering the device off and on.

Bluetooth Music Playback Control

Instructions on how to pause and resume music playback via the Bluetooth button.