Gardeners Titan A-Frame Trellis User Manual

V Rev /#
Titan A-Frame Trellis
Growing squash and cucumbers on a trellis saves space, reduces disease problems and makes harvesting a breeze. Titan A-Frame
Trellis is made from polyethylene-coated steel that will last for years to come. The polyethylene is non-degradable and provides a
clean look while protecting the steel from the elements. The steel tubing provides strength and durability, yet is also lightweight and
easy to assemble.
Parts List
() Top Supports
() Staked Supports
() Support Connectors
() Trellis Braces
() Sure-Clips
() Net Clips
() Netting
Assembly
NOTE: Assembly is easiest with  people.
Step 1. Identify and organize all parts on a clean, level surface.
Step 2. Form one side of the Trellis by attaching two Staked Supports to a Top Support using
the Support Connectors (Figure ). Repeat to make the other side of the Trellis.
Step 3. Place a Trellis Support into the clips on top of the Side Supports, as shown in Figure .
Carefully stand the Trellis upright, spreading the legs apart to keep it stable.
Step 4. Place a Trellis Brace against one side of the Trellis approximately "
from the bottom, as shown in Figure . Attach it to the Staked Supports using Sure-Clips
and the instructions below:
Tip: When attaching a Trellis Brace using the Sure-Clips, remember that the Brace should always be on the
outside of the Trellis and that the curved part of the Clips (Figure 4) will always be facing towards the
inside of the A-Frame Trellis.
Slide the looped end of a Sure-Clip over one end of the Brace (Figure ) and position it so the rounded part
of the Clip fits around the side of the Trellis. Bend the open ends of the Clip around the Trellis Brace,
securing the Sure-Clip into place. NOTE: This may take some extra strength as the Clips are made to be
tight. Repeat to attach the other side of the Brace.
Step 5. Repeat Step  to attach another Trellis Brace to the other
side of the Trellis.
over please
Staked
Supports
Support
Connectors
Top Support
Figure 1
Trellis Support
Side Supports
Figure 2
Figure 4
The curved part of the Sure-Clip will
always be facing towards the inside of
the A-Frame Trellis.
Figure 3
Trellis Support
Side Support
Sure-Clip

Gardeners Titan A-Frame Trellis Specifications

General

Brand	Gardeners
Model	Titan A-Frame Trellis
Category	Lawn and Garden Equipment
Language	English

Summary

Titan A-Frame Trellis Assembly

Identify and Organize Parts

Prepare all components by identifying and organizing them on a clean, level surface before assembly.

Form Trellis Sides

Attach two Staked Supports to a Top Support using Connectors to create one side, then repeat for the other side.

Stand Trellis Upright

Place a Trellis Support into the clips on top of the Side Supports and carefully stand the Trellis upright.

Attach Trellis Brace

Attach a Trellis Brace against one side of the Trellis approximately 14" from the bottom using Sure-Clips.

Attach Second Trellis Brace

Repeat the brace attachment process to secure another Trellis Brace to the other side of the Trellis.

Attach Remaining Trellis Supports

Attach the remaining eight Trellis Supports to the front and back of the Trellis, ensuring even spread.

Spread Netting Over Frame

Unfold the Netting and spread it over the Frame, looping it into the hooks on the ends of the Trellis Supports.

Secure Netting with Clips

Place Net Clips along the sides of the Trellis to secure the Netting to the frame by pressing down on the tab.

Position and Secure Trellis

Place the Trellis in a protected location and press Staked Supports into the ground at least 12-14" for stability.