To Next PageTo Next Page
Need help?Do you have a question about the Garmin GFC 600H and is the answer not in the manual?
Describes the manual's design for maintaining the GFC 600H Flight Control System.
Details maintenance and ICAs for the GFC 600H FCS installed per STC SR02647SE.
Lists acronyms and abbreviations used throughout the manual.
Describes the 2-axis (optional 3rd axis) flight control system and its functions.
Explains the digital helicopter flight control system and its capabilities.
Describes the system's function in stabilizing the aircraft and holding a reference attitude.
Describes the H-ESP system's capabilities for stability and protection.
Explains the higher level modes available with the GFC 600H FCS.
Details the GMC 605H controller's front panel, functions, and maintenance interface.
Describes the GFS 83 servo variants and their function in the GFC 600H system.
Details primary AHRS, Air Data, Magnetometer, GPS/SBAS, and Collective Position Sensor.
Lists the operational voltage and current draw for GFC 600H system LRUs.
Details the GMC 605H Mode Controller's modes of operation.
Describes the GMC 605H's interface for mode selections and annunciations.
Explains the GMC 605H display layout and annunciation descriptions.
Summarizes the functions of pilot controls located on the cyclic grip.
Depicts visual alerts and annunciations seen on a Garmin GDU.
Explains how to enter and navigate the GMC 605H Configuration mode.
Covers software updates for GMC 605H, GFS 83, and remote sensors like GSU/GRS.
States that the GFC 600H is airworthy when installed, configured, and maintained per the manual.
Describes the 'on condition' servicing strategy for GFC 600H FCS equipment.
Lists periodic maintenance intervals and associated procedures.
Details required visual inspections of GFC 600H FCS LRUs and associated wiring.
Describes possible symptoms and recommended actions for troubleshooting the GFC 600H FCS.
Details troubleshooting for the GMC 605H Mode Controller, including LED indicators and CAS messages.
Covers troubleshooting for GMC 605H LED indicators and Crew Alerting System messages.
Provides troubleshooting for AHRS/ADC faults and connector pinouts.
Lists connector information and pin functions for GFC 600H FCS LRUs.
Details removal and re-installation procedures for the GMC 605H Mode Controller.
Outlines removal and re-installation procedures for the GFS 83 servos.
Details removal and re-installation of servo control linkage, output arm, and shear fuse.
Provides procedures for removing and reinstalling the GSU 75H ADAHRS.
Details removal and re-installation procedures for the GRS 79H AHRS.
Covers configuration and checkout for the GMC 605H Mode Controller.
Details configuration and checkout for the GFS 83 servos.
Presents methods for performing GFS 83 servo range calibration.
Covers calibration for the Collective Position Sensor.
Describes post-installation calibration procedures for the GFC 600H system.
Describes the procedure for calibrating AHRS pitch/roll offset.
Details the procedure for testing magnetic interference using a GDU.
Explains how to calibrate the magnetometer using a compass rose or sight compass.
Describes performing a compass swing to verify AHRS heading accuracy.
Details information to be recorded in maintenance logs after return-to-service.
Describes procedures to be performed with external power and GMC 605H in Configuration mode.
Describes the procedure to test the autopilot disconnect audio tone.
Outlines procedures for verifying GFC 600H FCS operation in Normal mode.
Details the steps to verify the FCS pre-flight test status and annunciations.
Provides fields for recording general installation details.
Documents GFC 600H FCS interfaces with installed Garmin equipment.
Provides a structured log for GFC 600H FCS configuration settings.
Describes the manual's design for maintaining the GFC 600H Flight Control System.
Details maintenance and ICAs for the GFC 600H FCS installed per STC SR02647SE.
Lists acronyms and abbreviations used throughout the manual.
Describes the 2-axis (optional 3rd axis) flight control system and its functions.
Explains the digital helicopter flight control system and its capabilities.
Describes the system's function in stabilizing the aircraft and holding a reference attitude.
Describes the H-ESP system's capabilities for stability and protection.
Explains the higher level modes available with the GFC 600H FCS.
Details the GMC 605H controller's front panel, functions, and maintenance interface.
Describes the GFS 83 servo variants and their function in the GFC 600H system.
Details primary AHRS, Air Data, Magnetometer, GPS/SBAS, and Collective Position Sensor.
Lists the operational voltage and current draw for GFC 600H system LRUs.
Details the GMC 605H Mode Controller's modes of operation.
Describes the GMC 605H's interface for mode selections and annunciations.
Explains the GMC 605H display layout and annunciation descriptions.
Summarizes the functions of pilot controls located on the cyclic grip.
Depicts visual alerts and annunciations seen on a Garmin GDU.
Explains how to enter and navigate the GMC 605H Configuration mode.
Covers software updates for GMC 605H, GFS 83, and remote sensors like GSU/GRS.
States that the GFC 600H is airworthy when installed, configured, and maintained per the manual.
Describes the 'on condition' servicing strategy for GFC 600H FCS equipment.
Lists periodic maintenance intervals and associated procedures.
Details required visual inspections of GFC 600H FCS LRUs and associated wiring.
Describes possible symptoms and recommended actions for troubleshooting the GFC 600H FCS.
Details troubleshooting for the GMC 605H Mode Controller, including LED indicators and CAS messages.
Covers troubleshooting for GMC 605H LED indicators and Crew Alerting System messages.
Provides troubleshooting for AHRS/ADC faults and connector pinouts.
Lists connector information and pin functions for GFC 600H FCS LRUs.
Details removal and re-installation procedures for the GMC 605H Mode Controller.
Outlines removal and re-installation procedures for the GFS 83 servos.
Details removal and re-installation of servo control linkage, output arm, and shear fuse.
Provides procedures for removing and reinstalling the GSU 75H ADAHRS.
Details removal and re-installation procedures for the GRS 79H AHRS.
Covers configuration and checkout for the GMC 605H Mode Controller.
Details configuration and checkout for the GFS 83 servos.
Presents methods for performing GFS 83 servo range calibration.
Covers calibration for the Collective Position Sensor.
Describes post-installation calibration procedures for the GFC 600H system.
Describes the procedure for calibrating AHRS pitch/roll offset.
Details the procedure for testing magnetic interference using a GDU.
Explains how to calibrate the magnetometer using a compass rose or sight compass.
Describes performing a compass swing to verify AHRS heading accuracy.
Details information to be recorded in maintenance logs after return-to-service.
Describes procedures to be performed with external power and GMC 605H in Configuration mode.
Describes the procedure to test the autopilot disconnect audio tone.
Outlines procedures for verifying GFC 600H FCS operation in Normal mode.
Details the steps to verify the FCS pre-flight test status and annunciations.
Provides fields for recording general installation details.
Documents GFC 600H FCS interfaces with installed Garmin equipment.
Provides a structured log for GFC 600H FCS configuration settings.
General| Brand | Garmin |
|---|---|
| Model | GFC 600H |
| Category | Control Systems |
| Language | English |
