Model 21518
00023889 (Rev. 0 DOM E/S)
08-03
Printed in China
101 West 103rd St.
Indianapolis, IN 46290-1102
© 2008 Thomson Inc.
Trademark(s) ® Registered
Marca(s) Registrada(s)
No dial tone
• Check and repeat installation steps:
Ensure the AC power adaptor is connected to a working electrical outlet .
Ensure the telephone line cord is connected to the GE-21518 and the wall jack.
• Connect another phone to the same jack; if there is still no dial tone, the
problem might be your wiring or local service.
You experience static, noise, or fading in and out
• Your Bluetooth cell phone may be too close or out of range from the GE-21518,
move it to a distance of 2 feet to 10 feet.
• Your Bluetooth cell phone may be receiving interference from another cell
phone, move it to a distance of 2 feet to 10 feet away.
• Make sure the GE-21518 is not plugged into an outlet with another household
appliance. If necessary, relocate the GE-21518.
Unit locks up
• Unp lug the AC power adaptor from the wa ll outlet and the back of the
GE-21518, wait for 5 seconds and reconnect.
• Aluminum siding.
• Foil backing on insulation.
• Heating ducts and other metal construction that can shield radio signals.
• You’re too close to appliances such as microwaves, stoves, computers, etc.
• Atmospheric conditions, such as strong storms.
• The GE-21518 is installed in the basement or lower oor of the house.
• The GE-21518 is plugged into AC outlet with other electronic phones.
To keep your unit working and looking good, follow these guidelines:
• Clean the GE-21518, with a soft cloth.
• Never use a strong cleaning agent or abrasive powder because this will damage
the nish.
• Retain the original packaging, if need to ship the phone at a later date arises.
If trouble is experienced with this equipment, for warranty information, please contact
customer service at . If the equipment is causing harm to the telephone
network, the telephone company may require that you disconnect the equipment until the
problem is resolved.
Any unauthorized repairs, changes or modications not expressly approved by Thomson Inc.
could void the user’s authority to operate this product. For instructions on how to obtain a
replacement unit, refer to the warranty included in this guide or call customer service at
.
Or refer inquiries to:
Attach your sales receipt to this booklet for future reference or jot down the date this product
was purchased or received as a gift. This information will be valuable if service should be
required during the warranty period.
Purchase date
Name of store
To place order, have your Visa, MasterCard, or Discover Card ready and call toll-free
. A shipping and handling fee will be charged upon ordering. We are
required by law to collect appropriate sales tax for each individual state, country,
and locality to which the merchandise is being sent. Items are subject to availability.
• Defects in materials or workmanship.
• One year, from date of purchase.
(The warranty period for rental units begins with the rst rental or 45 days from date of
shipment to the rental rm, whichever comes rst.)
• Provide you with a new unit. The exchange unit is under warranty for the remainder of the
original product’s warranty period.
• Properly pack your unit. Include any cables, etc., which were originally provided with the
product. We recommend using the original carton and packing materials.
• ”Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that
the product is within the warranty period, must be presented to obtain warranty service.”
For rental rms, proof of rst rental is also required. Also print your name and address and
a description of the defect. Send via standard UPS or its equivalent to:
• Insure your shipment for loss or damage. Thomson Inc. accepts no liability in case of
damage or loss.
• A new unit will be shipped to you freight prepaid.
does not
• Customer instruction. (Your Owner’s Manual provides information regarding operating
instructions and user controls. Any additional information, should be obtained from your
dealer.)
• Installation and setup service adjustments.
• Batteries.
• Damage from misuse or neglect.
• Products which have been modied or incorporated into other products.
• Products purchased or serviced outside the USA.
• Acts of nature, such as but not limited to lightning damage.
• Please complete and mail the Product Registration Card packed with your unit. It will make
it easier to contact you should it ever be necessary. The return of the card is not required
for warranty coverage.
• Some states do not allow the exclusion nor limitation of incidental or consequential
damages, or limitations on how long an implied warranty lasts so the above limitations or
exclusions may not apply to you.
• This warranty gives you specic legal rights, and you also may have other rights that vary
from state to state.
• This warranty does not apply. Contact your dealer for warranty information.
Your telephone equipment is approved for connection to the Public Switched Telephone
Network and is in compliance with parts 15 and 68, FCC Rules and Regulations and the
Technical Requirements for Telephone Terminal Equipment published by ACTA.
On the bottom of this equipment is a label indicating, among other information, the US
number and Ringer Equivalence Number (REN) for the equipment. You must, upon request,
provide this information to your telephone company.
The REN is useful in determining the number of devices you may connect to your telephone
line and still have all of these devices ring when your telephone number is called. In
most (but not all) areas, the sum of the RENs of all devices connected to one line should
not exceed 5. To be certain of the number of devices you may connect to your line as
determined by the REN, you should contact your local telephone company.
A plug and jack used to connect this equipment to the premises wiring and telephone
network must comply with the applicable FCC Part 68 rules and requirements adopted
by the ACTA. A compliant telephone cord and modular plug is provided with this product.
It is designed to be connected to a compatible modular jack that is also compliant. See
installation instructions for details.
• This equipment may not be used on coin service provided by the telephone company.
• Party lines are subject to state tariffs, and therefore, you may not be able to use your own
telephone equipment if you are on a party line. Check with your local telephone company.
• Notice must be given to the telephone company upon permanent disconnection of your
telephone from your line.
• If your home has specially wired alarm equipment connected to the telephone line,
ensure the installation of this product does not disable your alarm equipment. If you have
questions about what will disable alarm equipment, consult your telephone company or a
qualied installer.
Should your equipment cause trouble on your line which may harm the telephone network,
the telephone company shall, where practicable, notify you that temporary discontinuance
of service may be required. Where prior notice is not practicable and the circumstances
warrant such action, the telephone company may temporarily discontinue service
immediately. In case of such temporary discontinuance, the telephone company must: (1)
promptly notify you of such temporary discontinuance; (2) afford you the opportunity to
correct the situation; and (3) inform you of your right to bring a complaint to the Commission
pursuant to procedures set forth in Subpart E of Part 68, FCC Rules and Regulations.
The telephone company may make changes in its communications facilities, equipment,
operations or procedures where such action is required in the operation of its business and
not inconsistent with FCC Rules and Regulations. If these changes are expected to affect the
use or performance of your telephone equipment, the telephone company must give you
adequate notice, in writing, to allow you to maintain uninterrupted service.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference; and (2) This device must accept
any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation.
Privacy of Communications may not be ensured when using this product.
If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna (that is, the antenna for radio or television
that is “receiving” the interference).
• Reorient or relocate and increase the separation between the telecommunications
equipment and receiving antenna.
• Connect the telecommunications equipment into an outlet on a circuit different from that
to which the receiving antenna is connected.
If these measures do not eliminate the interference, please consult your dealer or an
experienced radio/television technician for additional suggestions. Also, the Federal
Communications Commission has prepared a helpful booklet, “How To Identify and Resolve
Radio/TV Interference Problems.” This booklet is available from the U.S. Government Printing
Ofce, Washington, D.C. 20402. Please specify stock number 004-000-00345-4 when ordering
copies.
Notice: The changes or modications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment .
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of 20
centimeters between the radiator and your body. This transmitter must not be co-located or
operated in conjunction with any other antenna or transmitter.”
IF you want to use the GE-21518 with your home phone
service, you need an RJ11C type modular telephone jack,
which might look like the one pictured here, installed in your
home. If you don’t have a modular jack, call your local phone
company to nd out how to get one installed.
Make sure your package includes the items shown here.
• Avoid sources of noise and heat, such as motors, uorescent lighting,
microwave ovens, heating appliances and direct sunlight.
• Avoid areas of excessive dust, moisture and low temperature.
• Avoid other cordless telephones or personal computers.
• Never install telephone wiring during a lightning storm.
• Never install telephone jacks in wet locations unless the jack is specically
designed for wet locations.
• Never touch non-insulated telephone wires or terminals, unless the telephone
line has been disconnected at the network interface.
• Use caution when installing or modifying telephone lines.
Choose an area near an electrical outlet and a modular telephone jack (RJ11) and
place the GE-21518 on a level surface, such as a desktop or tabletop.
1. Connect one end of telephone line cord into the GE-21518 LINE jack and the
opposite end into a modular telephone jack. (This step is not necessary if you do
not have home phone service and/or only wish to connect a single phone to your
adaptor.)
2. Connect the telephone line cord of current home phone to PHONE jack of
the GE-21518.
3. Plug the AC power adaptor into an electrical outlet and connect it to the power
jack of the GE-21518.
4. The red LED of the GE-21518 will illuminate.
The GE-21518 supports a maximum of two Bluetooth cell phones.
1. Press and hold the button until it begins ashing, the GE-21518 enters
into pairing mode. To stop pairing, press again.
2. Refer to the instruction manual of your Bluetooth cell phone for the proper
procedure to add and pair a new phone.
3. Use the number keys to enter the default on the Bluetooth cell phone.
When the phone is paired and connected successfully, the CELL 1 indicator of the
GE-21518 will illuminate.
Press and hold the button again and the connection will resume.
Press and release the button to disconnect the Bluetooth cell phone. The
indicator will no longer be illuminated.
Press and hold the button for 5 seconds to cancel cell 1 pairing, the CELL 1
indicator will no longer be illuminated.
1. Pick up the handset of your telephone and listen for dial tone.
2. Dial the desired number. If telephone line is not connected or in-use by other
phones, a warning tone of three beeps will sound.
1. Pick up handset of your telephone and listen for dial tone. (If telephone line is not
connected or in-use by other phones, a warning tone of three beeps will sound).
2. Dial a sequence of: , then to make a
cellular call via CELL 1.
Pick up handset of your telephone and operate in usual manner.
When the telephone line is in-use by another phone in your home you may join in on
that call.
1. Pick up the handset of your telephone, (a warning tone of three beeps will sound).
2. Dial,,, to connect to ongoing call.
To Next Page
Need help?
General