Genesis ZIRCON 500 - User Manual; Manuel de Lutilisateur

4 5| |
• Move the switch located on the bottom of the mouse to 2.4G position
• Connect receiver to a free USB port on your computer
• The operating system will automatically install the required drivers
• The mouse is ready for use
Note:
• The device is equipped with intelligent technology for energy management. When
the mouse enter into hibernation (sleep) mode, press any button of the mouse for
its revival.
• The mouse is equipped with an ON/OFF switch to save the battery power when not
in use for longer period.
Tips:
• To get the best performance of wireless connection and reduce latency, connect
the USB receiver as close as possible to the mouse and make sure that there are no
obstacles between the mouse and the receiver that can interfere with the wireless
signal.
• In wireless mode set the polling rate to 500 Hz to get better smoothness performance
of sensor.
DPI | BT MODE SWITCH
• Short press DPI|BT mode switch to change resolution
• Hold DPI|BT mode switch for about 5 seconds to change Bluetooth channel between
BT1|BT2
CHARGING THE BATTERY
• Connect the included USB-C cable to the mouse
• Connect USB plug to a suitable power source (max. output DC 5V 0,5A)
• When the battery is fully charged, the DPI indicators will stop moving.
Note: When the battery level is too low, the DPI indicator will starts ashing.
Caution: Please charge the battery every 3 months, if you do not use the mouse for a
long time. Long-term storage of the mouse with low battery level, or using the chargers
with power over 5V 0,5A may damage the battery.
FR - MANUEL DE L’UTILISATEUR
1. 5 boutons programmables
2. Microcommutateurs mécaniques à une durée de vie jusqu’à 60 millions de clics
3. Capteur optique précis à une résolution de 10000DPI
4. Logiciel avancé avec éditeur de macros/prols
5. Mémoire intégrée
6. Triple mode de communication (Bluetooth | 2.4GHz | USB)
7. Compartiment de rangement pour le récepteur Nano
8. Batterie intégrée
INSTALLATION
• Connectez le câble à un port USB libre de l’ordinateur. Lors de la première connexion,
attendez environ 15 secondes jusqu’à ce que les pilotes soient complètement installés
• La souris a un logiciel qui vous permet de dénir des fonctions avancées, il doit être
téléchargée à partir de notre site Web www.genesis-zone.com
• Ouvrez le dossier d’installation puis double-cliquez sur l’icône setup.exe
EN - USER MANUAL
1. 5 programmable buttons
2. Mechanical switches with lifetime up to 60 million presses
3. Precise optical sensor with up to 10000 DPI
4. Advanced software with macro/prole editor
5. Built-in memory
6. Triple communication mode (Bluetooth | 2.4GHz | USB)
7. Nano receiver storage
8. Built-in rechargeable battery
INSTALLATION
• Connect the cable to a free USB port on your computer, it is necessary to wait about
15 seconds for the rst connection until the drivers are fully installed.
• The mouse includes software that allows you to set up advanced features, if you want
to use these features, you need to download and install the software from our website
www.genesis-zone.com
• Open the installation folder and then double-click the setup.exe le.
• Follow the instruction to install the program.
• After a successful installation, the software icon appears on the main bottom panel.
Double-clicking the icon opens the settings interface.
WIRED MODE
The mouse will switch to wired mode automatically once you connect USB cable to the
mouse and computer.
Tips:
• Wired mode oers better smoothness performance of sensor than wireless mode, for
best results set the polling rate to 1000 Hz.
• Wired mode allows simultaneous using of the mouse and charging the battery.
WIRELESS MODE
Pairing a new device with mouse in Bluetooth mode
• Move the switch located at the bottom of the mouse to BT position
• Turn ON Bluetooth in device which you want to pair with the mouse
• Use the button for changing the channel located on the bottom of the mouse, select
the channel BT1 or BT2 and then hold down at same time the left button + scroll +
right button for about 5 seconds to enter into pairing mode. The LED diode will start
ashing rapidly
• Then go to the Bluetooth settings on your device and select from the list of mouse
Zircon 500
• After successful pairing, the LED on the mouse will stop ashing
• The mouse is ready for use
Connecting the mouse with the previously paired device
• Turn ON Bluetooth on your device that you have previously paired with the mouse
• Switch the mouse into BT mode or wake it up from hibernation
• The mouse will automatically connect with the device
Connection of mouse via USB receiver
• Turn ON your computer or other compatible device