Genetec omnicast 4.8 SR3 - User Manual

101 pages

Save Page as PDF

To Next Page

To Next Page

Loading...

Omnicast

Video Unit Configuration Guide

4.8 SR3

Click here for the most recent version of this document.

Table of Contents

Default Chapter2
- Copyright Notice2
- Table of Contents3
- About this Guide7
- Video Unit Configuration8
All Manufacturers9
- Troubleshooting H.264 Video Streaming Enable Audio out Anti-Jitter Buffering9
Acti11
- Configuring Network Connection11
- Select Acti Video Streams11
- Upgrading Acti Unit Firmware11
Arecont12
- Configure Arecont Cropped Field of View12
- Configuring Arecont Camera Image Settings12
- Upgrading Arecont Unit Firmware17
- Configuring Arecont H.264 Units17
Ateme18
- Configure VSIP-2 Units18
- Configure VSS-441-R4TE Units19
Axis21
- Configure Axis H.264 Cameras21
- Configure Recording Schedules21
- Configure Trickling for Axis Units22
- Configuring the Axis T8310 Video Surveillance Control Board26
- Configure Multi-View Areas31
- Creating PTZ Patterns32
  - Configure PTZ Patterns32
  - Edit PTZ Presets33
Bosch34
- Configure Video Analytics34
- Configuring Bosch H.264 Units35
  - Configure the Video Resolution35
- Configure Bosch Audio Inputs36
- Configuring Bosch Divar 700 Dvrs37
- Configuring Bosch VRM Units39
  - Enable Audio Recording40
- Configure the Bosch Intuikey CCTV Keyboard41
- Configuring Bosch Units to Receive Hardware Motion Detection Events44
- Configuring the VJT XTCXF Transcoder45
Basler46
- Change the Default Port for Input Pin Events46
- Configuring Basler Units47
  - Set the Encoder Type for All Video Streams47
  - Configure the Frame Rate48
- Configure Basler BIP2 Input/Output Pins49
- Configure Basler BIP2-640C-Dn Units49
Canon50
- Configuring Canon VB-C60 and VB-C500D Units50
Cisco52
Comtex53
- Configure WB-H811 Units53
- Configure PTZ for WB-H811 Units53
- Dynacolor54
- Epiphan55
- Configure VGA Broadcaster Lite Units55
Interlogix57
- Configure Discovery 105-E (UVE-101) Units57
  - Enable Software Motion Detection58
- Configuring Visiowave Units58
Iqinvision61
- Configuring Virtual Zones61
- Using H.264 Multicast Streaming61
Mango DSP62
- Configure Input Pin Wiring63
- Configure Input Pin Events on the Standby Archiver63
- Change the Default Port for Input Pin Events64
Mavix65
- Configuring Mediaracer Units65
- Configure Mediaracer 150 and 152 Units68
- Configure Mediaracer 250 Units69
  - Select H.264 or MPEG-4 Streaming69
  - Configure the Stream Settings70
Otn71
- Configuring Mvidipv4 Units71
  - Disable Igmpv3 Support71
  - Enable MPEG-4 Start Code Lookup Offset72
Panasonic73
- Configuring H.264 Software Motion Detection73
- Configuring Multi-Streaming in MJPEG73
- Configuring I/O Pins74
- Configure Capture Resolutions75
- Configuring Edge Analytics for WJ-NT314 Units75
- Configuring WV-SC385 (DG-SC385) Units75
- Configure WJ-GXE500 (DG-GXE500) Units76
- Use Auto-Pan with Panasonic Units76
Pelco78
- Configuring Motion Detection78
- Adding Net54Xx Encoder Series78
- Configuring Dual-Streaming for Pelco IP Series78
- Configuring NET5301T Units78
- Configuring Pelco Sarix Units79
- Naming Sarix Spectra HD PTZ Preset Tours79
- Configuring the CM9760-CC1 for Use with the Pelco DMR Protocol79
Samsung83
- Configure SNP-3750 Units83
- Configure Samsung ONVIF Units84
Sanyo85
- Configure VCC-HD5X00 Units85
- Add Sanyo ONVIF Units85
Sony86
- Configure Sony 5Th Generation Cameras86
- Creating Sony PTZ Patterns86
- Using the Copy Configuration Tool89
- Configure Sony SNC-RZ30N Cameras90
- Configure Sony Edge Recording and Video Trickling91
- Maintaining 4:3 Aspect Ratio for the SNC-ZP55094
- Configuring 6Th Generation Units to Stream at 60 Frames Per Second95
- Enabling Wide Dynamic Range (View-DR)95
UDP Technology97
Verint98
- Configure S1808E-A and S1816E-A Units98
Vivotek99
- Configure IP8161 Units99
- Product Documentation100
- Technical Support101

Need help?

Do you have a question about the Genetec omnicast 4.8 SR3 and is the answer not in the manual?

Summary

Video unit configuration

ACTi

Additional configuration steps for ACTi units in Omnicast.

Arecont

Additional configuration steps for Arecont units in Omnicast.

ATEME

Additional configuration steps for ATEME units in Omnicast.

Axis

Additional configuration steps for Axis units in Omnicast.

Bosch

Additional configuration steps for Bosch units in Omnicast.

Basler

Additional configuration steps for Basler units in Omnicast.

Canon

Additional configuration steps for Canon units in Omnicast.

Cisco

Comtex

Dynacolor

Epiphan

Interlogix

IQinVision

Mango DSP

Mavix

OTN

Panasonic

Pelco

Samsung

Sanyo

Sony

UDP Technology

Verint

Vivotek

Technical support

Information on obtaining technical support and additional resources.

Genetec omnicast 4.8 SR3 Specifications

General

Version	4.8 SR3
Operating System	Windows Server 2008 R2, Windows 7, Windows 8, Windows Server 2012
Database	Microsoft SQL Server 2008 R2, Microsoft SQL Server 2012
Video Compression	H.264, MJPEG, MPEG-4
Supported Cameras	various manufacturers
Maximum Cameras per Server	Varies by configuration
Archiving	configurable retention policies