What to do if my Gerni Super 130.3 machine refuses to start?
If your Gerni Pressure Washer doesn't start, ensure it's properly plugged in and try a different socket. Replace the fuse if necessary. Test other machines on the same socket to rule out electrical issues. Avoid using an extension cable, as it may cause insufficient power.
What to do if Gerni Pressure Washer fuse blows?
If the fuse blows in your Gerni Pressure Washer, it might be too small. Replace it with a fuse that has a higher amperage rating than the machine's consumption. You can also try using the machine without an extension cable.
What to do if my Gerni Pressure Washer stops?
If your Gerni Pressure Washer stops, the fuse may have blown, so replace it. Also, the mains voltage might be incorrect; check that it corresponds to the specification on the model tag. The thermal sensor may have activated; if so, leave the washer for 5 minutes to cool down. Finally, the nozzle may be partially blocked; clean the nozzle (see section 7).
What to do if my Gerni Super 130.3 refuses to start?
If your Gerni Pressure Washer refuses to start, ensure it is properly plugged in. If it is, try another socket in case the current one is defective. Check the fuse and replace it if it has blown. Finally, if you are using an extension cable, try using the pressure washer without it, as the extension cable may be defective.
Why does the fuse blow on my Gerni Pressure Washer?
The fuse blows because it is too small. Change to an installation higher than the amp consumption of the machine.
What to do if my Gerni Super 130.3 Pressure Washer starts, but no water comes out?
If your Gerni Pressure Washer starts but no water comes out, the pumps, hoses, accessories, or the mains water supply might be blocked. Allow frozen pumps, hoses, or accessories to thaw. Ensure the inlet water is connected. Clean the filter.
Why does my Gerni Pressure Washer machine keep stopping?
Your Gerni Pressure Washer might stop due to a blown fuse. Replace the fuse and switch on other machines. Also, ensure the mains voltage matches the specifications on the model tag. If the thermal sensor has activated, let the washer cool down for at least 5 minutes. Clean the nozzle.
Why is my Gerni Super 130.3 pulsating?
If your Gerni Pressure Washer is pulsating, it could be due to several reasons. First, run the machine with the trigger open until regular pressure resumes to remove air from the inlet hose. Ensure the water supply meets the specifications on the model tag, and avoid using long, thin hoses. Clean the water filter and straighten out any kinks in the hose.
Why does my Gerni Super 130.3 Pressure Washer have fluctuating pressure?
Fluctuating pressure in your Gerni Pressure Washer may be caused by the pump sucking air. Check all hoses and connections to ensure they are airtight. Clean and replace if needed.
Why does my Gerni Pressure Washer often start and stop by itself?
If your Gerni Pressure Washer often starts and stops by itself, the pump or spray handle might be leaking. Contact your nearest Gerni Service Centre.
Explains pictograms and their meaning for safety and operation.
Important safety warnings about aerosols, high pressure, children, and checking machine condition.
Advises using only original spare parts and recommended hoses/fittings for machine safety.
States the machine is not for persons with reduced capabilities or under the influence of substances.
Lists domestic uses of the machine and defines improper use.
Recommends wearing appropriate safety gear like non-slip shoes and goggles.
Instructions on securing the machine during transport to prevent slipping or tipping.
Advises using only Gerni-supplied or recommended cleaning agents.
Checks to perform before operation, like cord condition and trigger function.
Warnings and requirements for safe electrical connection, including RCD and certified electricians.
Guidelines for connecting to pressurized and pressure-less water supplies.
Warnings about operating in environments that could be dangerous, and risks during operation.
Instructions for safely stopping the machine, unplugging, and disconnecting hoses.
Always disconnect power before maintenance. Repairs by authorized workshops with original parts.
How to clean the water inlet filter to prevent clogging and damage.
Instructions for cleaning a clogged nozzle to maintain correct pressure.
Importance of keeping machine vents clean for cooling.
Recommends greasing O-rings for easy connection and to prevent drying.
Lists and identifies all operational parts of the machine with corresponding numbers.
Step-by-step guide for assembling the trolley handle and hose hook.
Instructions for attaching the quick coupling to the water inlet, ensuring filter is in place.
How to raise or lower the telescopic handle using the button.
How to attach and detach the high pressure hose to the spray handle and outlet.
Instructions for attaching spray lance, nozzles, and foam sprayer.
Detailed steps for connecting to pressurized and pressure-less water supplies.
Step-by-step guide to safely start the machine after connecting power and water.
Information on how to adjust pressure using the specific PR-nozzle.
How to mount the pressure washer on a wall for stationary use.
General advice for efficient high-pressure cleaning, mentioning accessories and detergents.
How to apply detergent and foam for effective cleaning without damaging surfaces.
Using brushes for additional mechanical cleaning effect on tough dirt.
Details tasks, recommended accessories, and cleaning methods for various applications.
Steps to safely shut down the machine, including flushing, stopping, and unplugging.
Instructions for storing the machine, including winding cables and storing accessories.
A table listing common symptoms, their causes, and recommended actions for troubleshooting.
Advises using only original accessories and detergents for best performance.
Details warranty periods for the machine and motor pump, and conditions for repairs.
Lists technical data like voltage, power, pressure, flow rate, and protection degrees.
Provides weight specifications and hand-arm vibration levels according to ISO standards.
Lists sound pressure and power levels for machines with and without hose reels.
Declares product compliance with relevant EU directives and standards for safety and EMC.
General| Brand | Gerni |
|---|---|
| Model | Super 130.3 |
| Category | Pressure Washer |
| Language | English |
To Next Page