Why won't my Gerni Classic 120.4 start?
If your Gerni Pressure Washer refuses to start, there are several possible reasons. First, ensure the machine is properly plugged into a working socket. Try a different socket to rule out a defective one. Also, check the fuse and replace it if it has blown. Finally, a defective extension cable could be the culprit; try using the pressure washer without it.
What to do if my Gerni Classic 120.4 Pressure Washer suddenly stops?
If your Gerni Pressure Washer suddenly stops, here's what to check: * Replace the fuse if it has blown. * Ensure the mains voltage corresponds to the specification on the model tag. * If the thermal sensor activated, leave the washer for 5 minutes to cool down. * Clean the nozzle, as a partially blocked nozzle can cause the machine to stop.
What to do if the fuse blows on my Gerni Classic 120.4?
If the fuse blows on your Gerni Pressure Washer, it might be too small. Change to an installation higher than the amp consumption of the machine. You may also try without the extension cable.
How to fix fluctuating pressure on my Gerni Pressure Washer?
Fluctuating pressure in your Gerni Pressure Washer can be due to several reasons. Check that all hoses and connections are airtight to prevent the pump from sucking air. For dirty, worn out, or stuck valves, contact your local Gerni Service center. If the pump seals are worn out, clean and replace them or refer to a local Gerni distributor.
Why is my Gerni Classic 120.4 Pressure Washer pulsating?
If your Gerni Pressure Washer is pulsating, it could be due to air in the inlet hose or pump. Allow the machine to run with the trigger open until regular working pressure resumes. Another cause could be an inadequate supply of mains water. Check that the water supply corresponds to the required specifications (see the model tag), and avoid using long, thin hoses (min. 1/2').
Explains symbols used to mark instructions for safety and ease of use.
Crucial safety warnings for operation, including aerosols, pressure, and electrical hazards.
Importance of using original spare parts and recommended hoses/fittings for safety.
Restrictions on use for persons with reduced capabilities or under influence.
Defines intended uses and recommends protective clothing for operation.
Guidelines for machine transport and advice on using recommended detergents.
Checks to perform on the machine before operation, including cord and parts.
Warnings and requirements for safe electrical connection, including voltage and RCD.
Details on extension cables and guidelines for connecting to water supplies.
Critical warnings for operation, like avoiding explosions, solvents, and directing the jet.
Procedures for safely stopping, cleaning, maintenance, and recycling.
Identifies and lists the various parts and components of the machine.
Step-by-step instructions for attaching the trolley handle and wheels.
Instructions for attaching the quick coupling to the water inlet, including filter check.
How to attach and detach the high pressure hose to the spray handle and machine.
Instructions for attaching the spray lance and various Click&Clean nozzles.
Connecting to pressurized and pressureless water supplies, including filter checks.
Procedures for safely shutting down, disconnecting, and cleaning the machine.
Recommendations for cleaning hoses, connectors, and nozzles for longevity.
How to clean the water inlet filter regularly to prevent pump damage.
Procedures for cleaning a clogged nozzle and keeping machine vents clear.
Importance of greasing O-rings for easy connection and coupling integrity.
Common causes and recommended actions for when the machine won't start.
Potential causes and solutions for inconsistent water pressure.
Explains warranty coverage, exclusions, and conditions for repairs.
Provides contact details for warranty assistance in Australia and New Zealand.
Technical details on voltage, frequency, power, and current ratings.
Technical details on pressure, water flow rates, and temperatures.
Physical specifications including weight, vibration, and sound pressure/power levels.
Lists standards and directives the product complies with for safety and EMC.
General| Max Pressure | 120 bar |
|---|---|
| Flow Rate | 420 L/h |
| Power | 1400 W |
| Hose Length | 5 m |
| Power Cable Length | 5 m |
| Voltage | 220-240 V |
| Frequency | 50 Hz |
To Next Page