GESTRA URB 60 - User Manual

To Next Page

Original Installation &

Operating Manual

Visual Display and Operating Unit

URB 60

819699-00

English

Main Page

Default Chapter2
- Table of Contents2
Content of this Manual5
Scope of Delivery/Product Package5
How to Use this Manual6
Illustrations and Symbols Used6
Hazard Symbols in this Manual6
Types of Warning7
URB 60 Specialist Terms and Abbreviations8
Usage for the Intended Purpose11
- IT Security and Rules for the Use of Ethernet Devices11
- Applicable Directives and Standards11
Improper Use12
Basic Safety Notes12
Required Personnel Qualifications13
Notes on Product Liability13
Function14
- Limitations14
Technical Data15
Factory Settings16
Name Plate/Identification17
Dimensions of the URB 6018
Installation Instructions18
Ports and Sockets on the URB 6019
Connecting the Supply Voltage20
Connecting the CAN Bus System20
- Bus Line, Cable Length and Cross-Section20
- Important Notes on Connecting the CAN Bus System21
- Pin Assignment of the CAN Bus Connector and Coupling for Non Pre-Wired Control Cables22
Operation and Navigation23
- User Interface (Example)23
- Operation23
- Colour Coding of Input and Status Fields24
- Automatic Functions24
- Entering Parameters Using the Virtual Keypad25
- Entering Parameters with Multilevel Password Security25
- Scroll Bar for Long Lists and Menus26
- General Recurring Icons and Functions26
Starting up for the First Time27
- Setup Wizard Settings27
Bringing the Boiler, Feedwater/Condensate Tank into Service (Group 128
Home Screen29
Alarms and Error Messages31
- Opening the Alarm History - the Complete List of All Alarms32
- Opening the Alarm and Error List Automatically32
System Settings33
Viewing CAN Bus Nodes34
Setting the Date/Time35
Password35
Network Settings36
Remote Maintenance/Software36
Device Settings37
System Information39
Selecting the Language40
Configuring the Level Controller41
- Testing the Relays of the Connected Level Controller42
- Pump Control42
- Setting Manual Control or the Control Point for Manual Pump Operation43
- Switching Actuator Operation between Automatic and Manual43
- Valve Calibration in Manual Mode When a Feedback Potentiometer Is Connected to the NRR 2-6044
- Calibrating the Boiler Level45
- Setting the Level Controller46
- Guide to Setting Control Parameters46
- Setting the Level Controller for 3-Component Control47
Configuring the Conductivity Controller48
- Standby Mode49
- Testing the Relays of the Connected Conductivity Controller49
- Continuous Blowdown Valve50
- Continuous Blowdown Valve - Calibrating the Feedback Potentiometer for the Valve Position Display51
- Setting the Intermittent Blowdown and Automatic Flush Function52
- Setting a Correction Factor and Temperature Compensation for the Current Conductivity Reading53
- Setting Safety Parameters54
- Setting the Control Parameters55
- Guide to Setting Control Parameters55
Opening the Limiter Overview56
- Setting Safety Parameters57
- Testing the Limiter58
System Malfunctions59
- Display of System Malfunctions in the Alarm and Error List Using Fault Codes59
  - Fault Codes for the URS 60/URS 61 Safety Control Unit59
  - Fault Codes for the NRR 2-60 / NRR 2-61 Level Controller, LRR 1-60 Conductivity Controller and URW 60 Universal Converter60
- Common Faults During Use62
What to Do in the Event of System Malfunctions62
- Checking Installation and Function62
Data Exchange Via Modbus TCP63
Taking out of Service63
Disposal63
Returning Decontaminated Equipment64
EU Declaration of Conformity64

Need help?

Do you have a question about the GESTRA URB 60 and is the answer not in the manual?

GESTRA URB 60 Specifications

General

Brand	GESTRA
Model	URB 60
Category	Monitor
Language	English

GESTRA URB 60 - User Manual

Table of Contents

GESTRA URB 60 Specifications