Getronic Gt613 User Manual

1
GT613UKRev02.p65
GT613 - 614 - 615 FITTING INSTRUCTIONS
GREY/BLACK
BATTERY
IGNITION KEY
RED
YELLOW/BLACK (RELAY OUTPUT)
+15/54
IGNITION SWITCHED LIVE
YELLOW
CUT
15 AMP FUSE
BROWN
EARTH
VEHICLE
RED/GREY
PINK
GREEN/BLACK
GREEN
GREEN/BROWN
ORANGE
Positive output when the
Additional sensors/modules
To the GREEN/BLACK wire
NEGATIVE command for the starter
PIN SWITCH
BOOT/BONNET
ORIGINAL DOOR
PINSWITCH
Connect to either near side or
off side indicator wire
Constant or intermittent output when the alarm is
being triggered (current max. 5A). With this wire it
is possible to drive the HORN relay, an electronic
siren (GT43) the parking lights or a after market satellite
system.
CONTROL UNIT
Connect to positive or negative depending on the
polarity required on the YELLOW/BLACK wire.
immobilisation (current max 80mA)
Additional relay
85
86
87
87A
30
M
Diode 1N4007
+15/54
* NOTE: it is possible to use the GT465 module
RED
BLACK
BLACK (RELAY COMMON)
CHECK LED
+12V
GT431
-
+
BROWN
PINK
GREEN/BLACK
GT632GT431
alarm is armed
(current max. 80mA)
on additional sensors/modules
+12V
STARTER MOTOR*
Tilt sensor adjustment
clockwise = more sensitive
anti-clockwise = less sensitive
(use the supplied screwdriver)
WHITE RED
or satellite system
INDICATORS
IMMOBILISATION
CORRECT
ABOVE THE DASHBOARD INCORRECT POSITIONS
CENTRE
DASHBOARD
POSITIONS
CONSOLE
RED WHITE
POSITIONING OF THE
GT431 ULTRASONIC SENSORS
POSITIONING OF THE GT 632
HYPERFREQUENCY SENSOR
WARNING: Incorrect installation will
increase the risk of water ingress
into the siren.
Make sure that the loom cover is
attached with supplied screws and
the sheath covers the neck of the
loom cover and secured with a cable
tie.
TRANSMITTING
SIDE
LED
ADJUSTMENT
TRIMMER
ADJUSTMENT
GT431
-
+
SENSITIVITY
ADJUSTMENT
It is advisable to place the alarm as
indicated in the figure to obtain the
maximum of performances by the
shock sensor. Note that the maximum
sensitivity is obtained with a 30°
angulation.
Correct alarm positioning for the shock sensor
SHOCK SENSOR
MINIMUM SENSITIVITY
SHOCK SENSOR M
AXIMUM SENSIITIVITY
70 degrees
30 degrees

Getronic Gt613 Specifications

General

Brand	Getronic
Model	Gt613
Category	Car Alarm
Language	English

Summary

GT613 - 614 - 615 Fitting Instructions

Correct Alarm Positioning for Shock Sensor

Advises on optimal placement of the shock sensor for maximum performance with a 30-degree angulation.

Positioning of GT431 Ultrasonic Sensors

Details the correct placement of ultrasonic sensors for optimal vehicle coverage.

Positioning of GT632 Hyperfrequency Sensor

Guides on the proper placement of the hyperfrequency sensor for effective operation.

Electrical Connections

DIP Switch Selectable Functions Explained

Details the functions selectable via DIP switches for alarm configuration and behavior.

Doors Lock/Unlock Impulses Self-Coding Procedure

Step-by-step guide to program the alarm for remote control lock/unlock impulses.

Emergency Disarming Function

Installation Check (Test Procedure)

Procedure to verify correct installation and functionality of the alarm system components.

GT431 Ultrasonic Sensor Operation Test

Tests the functionality and sensitivity of the GT431 ultrasonic sensors.

GT632 Hyperfrequency Sensor Operation Test

Tests the functionality and sensitivity of the GT632 hyperfrequency sensor.

Shock Sensor Operation Test

Procedure to test the shock sensor's responsiveness and adjust its sensitivity.

Exit from Test Procedure

Steps to correctly exit the installation test mode.

User Manual - How to Use the Alarm

Arm/Disarm the Alarm

Instructions on how to arm and disarm the alarm system using the original handset.

Electric Windows Closure Command Function

Explains the control of electric windows when the alarm is armed.

Alarm Protections

Details the various protections offered by the alarm system, such as immobilisation and sensor monitoring.

Check LED Indicator

Explains the function of the Check LED for indicating alarm states and triggered sensors.

Emergency Disarming

Provides instructions for disarming the alarm when the handset is not functional.