Gigabyte GA-Z68X-UD5-B3 - Page 51

- 51 - BIOS Setup
Onboard LAN Boot ROM
Allows you to decide whether to activate the boot ROM integrated with the onboard LAN chip.
(Default: Disabled)
Onboard USB3.0 Controller (Renesas D720200 USB 3.0 Controller)
Enables or disables the Renesas D720200 USB 3.0 controller. (Default: Enabled)
USB3.0 Turbo (Renesas D720200 USB 3.0 Controller)
Enables or disables the Turbo USB mode for the Renesas D720200 USB 3.0 controller. The actual per-
formance may vary depending on the number of devices being installed. (Default: Disabled)
eSATA3 Controller (Marvell 88SE9128 Chip, eSATA3 Connectors on the Back Panel)
Enables or disables the SATA controller integrated in the Marvell 88SE9128 chip. (Default: Enabled)
eSATA3 Ctrl Mode (Marvell 88SE9128 Chip, eSATA3 Connectors on the Back Panel)
 AllowsyoutodecidewhethertoconguretheSATAcontrollerintegratedintheMarvell88SE9128chip
to AHCI mode.
IDE   CongurestheSATAcontrollertoIDEmode.(Default)
AHCI   Congures theSATA controllertoAHCImode.Advanced HostController Interface
(AHCI)isaninterfacespecicationthatallowsthestoragedrivertoenableadvanced
Serial ATA features such as Native Command Queuing and hot plug.
eSATA3 Transaction Mode (Marvell 88SE9128 Chip, eSATA3 Connectors on the Back
Panel)
Allows you to decide whether to enable RAID for the Marvell 88SE9128 SATA controller.
Bypass Disables RAID.
Fw Mode Enables RAID. (Default)
Auto   LetstheBIOScongurethissettingdependingontheharddrivesconnected.
In case you want to switch to Fw Mode from other modes and to be able to enter the eSATA3 RAID
Conguration screen, after selecting Fw Mode,besuretosavethesettingsandexitBIOSSetuprst
for the settings to take effect.
eSATA3 RAID Conguration (Marvell 88SE9128 Chip, eSATA3 Connectors on the Back
Panel)
 AllowsyoutocongureRAIDfortheMarvell88SE9128SATAcontroller.RefertoChapter5,"Congur-
ingSATAHardDrive(s),"forinstructionsonconguringaRAIDarray.
SATA3 Firmware Selection
 DetermineswhethertoautomaticallyupdatethermwareoftheMarvell88SE9128chip.
Onchip  Keepstheoriginalrmwareversion.
Auto   LetstheBIOSautomaticallyupdatethermwaretothelatestversion.(Default)
Auto   ForcestheBIOStoashthermwarewiththesameversionastheoneembeddedin
the system BIOS, even if it's not the latest one.
When a Cable Problem Occurs...
 Ifacableproblemoccursonaspeciedpairofwires,theStatuseldwillshowShort and then length
shown will be the approximate distance to the fault or short.
Example:
Part1-2 Status = Short / Length = 2m
Explanation: A fault or short might occur at about 2m on Part 1-2.
Note: Part 4-5 and Part 7-8 are not used in a 10/100 Mbps environment, so their Statuseldswillshow
Open, and the length shown is the approximate length of the attached LAN cable.