Gigabyte GA-Z68X-UD7-B3 - Page 53

- 53 - BIOS Setup
When a Cable Problem Occurs...
 Ifacableproblemoccursonaspeciedpairofwires,theStatuseldwillshowShort and then length
shown will be the approximate distance to the fault or short.
Example:
Part1-2 Status = Short / Length = 2m
Explanation: A fault or short might occur at about 2m on Part 1-2.
Note: Part 4-5 and Part 7-8 are not used in a 10/100 Mbps environment, so their Statuseldswillshow
Open, and the length shown is the approximate length of the attached LAN cable.
Start detecting at Port.....
Link Detected --> 100Mbps
Cable Length= 30m
Link Detected Displays transmission speed.
Cable Length Displays the approximate length of the attached LAN cable.
Note: The Gigabit hub will only operate at a speed of 10/100 Mbps in MS-DOS mode; it will operate at a
normal speed of 10/100/1000 Mbps in Windows mode or when the LAN Boot ROM is activated.
When No LAN Cable Is Attached...
If no LAN cable is attached to the motherboard, the StatuseldsofallfourpairsofwireswillshowOpen
and the Lengtheldsshow0m,asshowninthegureabove.
When LAN Cable Is Functioning Normally...
If no cable problem is detected on the LAN cable connected to a Gigabit hub or a 10/100 Mbps hub, the
following message will appear:
Onboard LAN1/LAN2 Boot ROM
Allows you to decide whether to activate the boot ROM integrated with the onboard LAN chip.
(Default: Disabled)
Onboard USB3.0 Controller (1st Renesas D720200 USB 3.0 Controller, 5 USB 3.0 Ports on
the Back Panel, Not Including the Upper USB 3.0 Port Next to the Audio Jacks)
 EnablesordisablestherstRenesasD720200USB3.0controller.(Default:Enabled)
USB3.0 Turbo (1st Renesas D720200 USB 3.0 Controller, 5 USB 3.0 Ports on the Back
Panel, Not Including the Upper USB 3.0 Port Next to the Audio Jacks)
 EnablesordisablestheTurboUSBmodefortherstRenesasD720200USB3.0controller.Theactual
performance may vary depending on the number of devices being installed. (Default: Disabled)
Onboard USB3.0 Controller2 (2nd Renesas D720200 USB 3.0 Controller, USB 3.0 Ports
routed to the onboard F_USB30_1/F_USB30_2 connector and the Upper USB 3.0 Port
Next to the Audio Jacks on the back panel)
Enables or disables the second Renesas D720200 USB 3.0 controller. (Default: Enabled)
GSATA3 Controller ( Marvell 88SE9128 Chip, GSATA3_6 and GSATA3_7 Connectors)
Enables or disables the SATA controller integrated in the Marvell 88SE9128 chip. (Default: Enabled)
GSATA3 Ctrl Mode ( Marvell 88SE9128 Chip, GSATA3_6 and GSATA3_7 Connectors)
 AllowsyoutodecidewhethertoconguretheSATAcontrollerintegratedintheMarvell88SE9128chip
to AHCI mode.
IDE   CongurestheSATAcontrollertoIDEmode.(Default)
AHCI   CongurestheSATAcontrollertoAHCImode.AdvancedHostControllerInterface
     (AHCI)isaninterfacespecicationthatallowsthestoragedrivertoenableadvanced
Serial ATA features such as Native Command Queuing and hot plug.