Glomex URANIA 2 V9331

Questions and Answers

F
floresveronicaJul 31, 2025
What to do if my Glomex URANIA 2 V9331 Antenna does not find the satellite and the LED is red?
- E
  ehintonJul 31, 2025
  If the Glomex Antenna's control unit LED is red and it cannot find the satellite, the issue might be due to obstructed satellite signals. Try moving the boat to a location with a clear view. Another reason may be that the boat is outside the signal coverage area. In that case, move back within the coverage area. If the boat is heaving within the first 60 seconds after turning on the equipment, turn off the equipment for 10 seconds, turn it on again and make sure that the boat is still or moves in a straight line during the first 60 seconds after being turned on. Finally, the SKEW adjustment might be wrong; in this case adjust the SKEW.
J
John WilliamsAug 4, 2025
What to do if my Glomex URANIA 2 V9331 Antenna has intermittent images for short periods?
- A
  Andrew RodriguezAug 4, 2025
  If you are experiencing intermittent images on your Glomex Antenna, it could be due to a few reasons. The satellite signals might be obstructed by masts, bridges, or on-board equipment. Try moving the boat to a location where the antenna has a clear view. Alternatively, the boat may be at the edge of the coverage area, so moving back within the coverage area might resolve the issue. Also, check the SKEW adjustment and adjust it if necessary.
Q
qwilsonAug 8, 2025
What to do if my Glomex URANIA 2 V9331 Antenna does not operate and the LED flashes red and green?
- C
  carrolltrevorAug 8, 2025
  If your Glomex Antenna is not working and the LED on the control unit flashes alternately red and green, it could be due to a loose or disconnected coaxial cable. Check the connection of the coaxial cables to ensure they are properly connected.
G
Gregory LeonardAug 12, 2025
Why Glomex Antenna does not operate and the LED on the control unit does not turn on?
- J
  Jennifer RuizAug 12, 2025
  If your Glomex Antenna is not operating and the LED on the control unit is off, it could be due to several reasons: a blown fuse (replace it), a wrong power supply cable connection (check the polarity), or a short-circuited coaxial cable (check the mounting of the coaxial cables).
J
jillianwhiteAug 16, 2025
What to do if my Glomex Antenna has no image on the TV, but the LED is green?
- B
  Brittany HurleyAug 17, 2025
  If you're not getting an image on your TV with your Glomex Antenna, but the control unit's LED is green, try these steps: turn off the control unit, turn on the receiver, and then turn the control unit back on. Ensure the TV is on and tuned to the AV channel. Also, verify that the SCART socket between the TV and the receiver is correctly connected. Finally, perform an automatic channel search in the receiver menu to update the channel list.
S
Steven PearsonAug 21, 2025
What to do if my Glomex URANIA 2 V9331 Antenna does not find the satellite and the LED flashes red and orange?
- C
  Carla WheelerAug 22, 2025
  If your Glomex Antenna is not finding the satellite and the LED flashes alternately red and orange, it could be due to obstructed satellite signals. Try moving the boat to allow an unobstructed view for the antenna. Also, the SKEW adjustment might be wrong; in this case adjust the SKEW.
J
Jessica KnightAug 26, 2025
Why is there no status message on the decoder of my Glomex URANIA 2 V9331 Antenna?
- T
  twilliamsAug 26, 2025
  If there is no status message on the decoder, ensure the satellite receiver is correctly installed.