GMV NGV A3 - 3.3 CONNECTIONS

ENG
NGV A3 VALVE
INSTALLATION, USE AND MAINTENANCE
22/ 53
10991483 EN -1.10 - 26.05.2023
3.3 CONNECTIONS
3.3.1 CONTROL PANEL INTERFACE
The input circuits are divided in two groups, both isolated from the card power supply:
• V0,V1,V2,VS with common V-
• D+ with common D-
Each group can be powered or by an external source within established limits, or directly by the card power,
connecting the commons (V- and/or D-) to the A-.
The interfacing with the control panel is made via removable terminal connectors defined as follows:
Connector X1, step 3,5 mm
Pos.
Mark
Features
Description
1
BH
Bus
Can bus H
2
BL
Bus
Can bus L
3
SH
Shield
Shield
Connector X2, step 5,0 mm
Pos.
Mark
Features
Description
1
11
10mA...2A
20...250V
Programmable output relay (refer to programming
menu and programmable functions chart)
2
12
3
21
10mA...2A
20...250V
Programmable output relay (refer to programming
menu and programmable functions chart)
4
22
5
31
10mA...2A
20...250V
Programmable output relay (refer to programming
menu and programmable functions chart)
6
32
7
41
10mA...2A
20...250V
Programmable output relay (refer to programming
menu and programmable functions chart)
8
42
Connector X3 step 3,5 mm
Pos.
Mark
Features
Description
1
50
10mA...2A
20...250V
Uscita RUN (NO)
2
51
10mA...2A
20...250V
Uscita RDY (NO)
3
52
10mA...2A
20...250V
Common
Connector X4, step 3,5 mm
Pos.
Mark
Features
Description
1
A-
Power: negative (-)
2
V-
Inputs: negative
Make a short circuit with A- if you use V+ as power
or connect to input negative pole.
3
VS
12...48Vdc,
10...40mA
Input command: upward
4
V0
Input command: speed: high (nominal speed)
5
V1
Input command: speed: medium
6
V2
Input command: speed: inspection
7
V3
Input command: speed: micro-levelling
8
V+
Power: positive common.
For input command circuits without voltage.
Do NOT use if input commands are under voltage
Connector X5, step 3,5 mm
Pos.
Mark
Features
Description
1
A+
Power: positive
2
PE
PE, ground
3
A-
Power: negative
4
A-
Power: negative
Connector X6, step 5,0 mm
Pos.
Mark
Features
Description
1
D+
12...48Vdc,
60...180Vdc
Input command: downward
2
D-
Input downward: negative
3
E+
Input command: emergency solenoid valve
4
E-
Input emergency solenoid valve: negative
BHBL S
50 51 52
11 12 21 22 31
32
41 42
X14
X15
X1
X3
X2

BHBL S
50 51 52
11 12 21 22 31
32
41 42
X14
X15
X1
X3
X2

BHBL S
50 51 52
11 12 21 22 31 32
41 42
X14
X15
A-
X1
X3
X2
52
V- VS V0
V1
V2 V3V+
A+PEA- A-
D+ D- E+ E-
1
3
A-
X3
X4
X6
X5
J6

52
V- VS V0
V1
V2 V3V+
A+PE A- A-
D+ D- E+ E-
1
3
A-
X3
X4
X6
X5
J6

52
V- VS V0
V1
V2 V3V+
A+PE A- A-
D+ D- E+ E-
1
3
A-
X3
X4
X6
X5
J6
