The GODIAG GT107 Gearbox Data Adapter ECU IMMO Kit is a specialized tool designed for automotive service technicians to work with DSG (Direct-Shift Gearbox) ECUs. It facilitates cloning, diagnosis, repair, and data manipulation (reading, writing, and adjusting) of DSG Gearbox ECUs using various programming tools such as PCMFlash, PCMTuner, and Kessv2.
Function Description:
The primary function of the GODIAG GT107 is to provide a reliable connection interface between the DSG gearbox ECU and diagnostic/programming tools. It supports a wide range of DSG gearbox models, including:
- Renault DCO/DC4 Gen2
- Honda LUK UDCT
- DQ200 (0AM) [WR/CK]
- DQ250C (02E) [RD/WR/CK]
- DQ250E/F (02E) [WR/CK]
- DQ200MQB/G2 (0CW) [WR/CK]
- DQ250MQB (0D9) [WR/CK]
- VL300/V30 (01J/0AN) [WR/CK]
- VL381 (0AW) [WR/CK]
- DL501/G2 (0B5) [WR/CK]
- DQ500 (0BH/0BT) [RD/WR/CK] (supports direct connection reading)
- Boot modes for various models (MICRO and EEPROM) including DQ200/MQB/G2, DQ250E/F/MQB, VL300/V30 BSL (FLASH and EEPROM), VL381, and DL501/G2.
The adapter allows for both "Auto" and "Manual" modes of operation, selectable via a switch on the GT107 unit. The "Auto" mode is recommended for reading and writing data, particularly with PCMFlash software, while the "Manual" mode is suitable for diagnosis and use with other software like Kessv2, and for specific ECU models such as DQ200, DQ250, and DQ500. For Kessv2 and similar software, a 120 ohm resistor switch needs to be pressed down.
The device is designed to ensure stable communication and power supply during critical operations like data reading and writing, which helps prevent ECU damage or data loss. It can be powered by a stable external 12V 4A-5A DC power supply or a vehicle battery, provided the battery voltage is at least 12V and has sufficient power for at least 30 minutes of operation.
Important Technical Specifications:
- Power Supply Requirement: 12V 4A-5A DC for stable operation when connecting the DSG gearbox in a workshop setting. If using a car battery, ensure 12V and sufficient power for 30 minutes.
- Operating Modes: "Auto" (switch popped up) for data reading/writing (recommended for PCMFlash), and "Manual" (switch pressed down) for diagnosis and other software.
- Resistor Switch: 120 ohm resistor switch for specific software like Kessv2.
- Supported ECUs: Extensive list of DSG gearbox ECUs including Renault DCO/DC4 Gen2, Honda LUK UDCT, VAG DQ series (DQ200, DQ250, DQ500), VL series (VL300, VL381), and DL series (DL501).
- Boot Mode Support: Includes support for MICRO and EEPROM boot modes for various DQ, VL, and DL series ECUs.
- Connectivity: Connects to the gearbox ECU, GODIAG ECU IMMO Prog AD (GT105), and J2534 passthru devices like PCMFlash or PCMTuner.
Usage Features:
- Ease of Connection: Provides clear wiring definitions for various DSG gearbox ECU interfaces (DQ200, DQ250, VL381, V30, VL300, DQ500, DL382, DL501, DC0/DC4 Gen2, LuK-UDCT), simplifying the setup process.
- Visual Communication Status: Allows users to clearly check the communication status during data reading and writing, enhancing operational confidence.
- Flexible Power Options: Can be powered by an external DC power supply or a vehicle battery, offering versatility in different working environments.
- Mode Selection: The "Auto" and "Manual" mode switch on the GT107 provides flexibility based on the specific operation (reading/writing vs. diagnosis) and software being used.
- Boot Mode Operation: For advanced operations like BSL (Boot Strap Loader) with VL300/V30, it requires drilling a small hole to insert a probe, which connects to the BOOT 1k ohm GND line of the GT107. Auto power is recommended for quickly identifying the pin on the board.
- Safety Precautions: Emphasizes the importance of using a stable power supply to prevent ECU damage and data loss. Users are advised to ensure the vehicle battery is adequately charged if used as a power source.
- Kit Contents: The package includes the Godiag ECU IMMO Prog AD (GT105), DSG Adapter (GT107), a power cord with battery clip, and a probe, providing a comprehensive solution.
Maintenance Features:
- User Manual Guidance: The manual provides detailed instructions and safety statements to guide users through proper operation and maintenance, minimizing risks to equipment and vehicles.
- Preventive Measures: Highlights the need for a stable and reliable power supply (12V 4A-5A) to prevent ECU damage or data loss during data reading and writing operations.
- IMMO Function Switch: Users are reminded to ensure the IMMO function switch on the Godiag ECU IMMO Prog AD (GT105) is in the "up" position (off) when connecting the power supply initially.
- Careful Handling: The manual implicitly encourages careful handling of the device and connections to avoid damage, especially during boot mode operations that involve physical probing of the ECU board.
- Software Compatibility: The device is designed to work with popular automotive programming software like PCMFlash, PCMTuner, and Kessv2, ensuring broad utility and compatibility with existing workshop setups.
The GODIAG GT107 is a robust and versatile tool for professionals engaged in DSG gearbox ECU maintenance, offering essential functionalities for data management and diagnostics with an emphasis on operational safety and reliability.
Need help?
To Next Page
General