1
LED Motion-Activated Battery Operated Security Light
Éclairage de sécurité à DEL activé par un mouvement et alimenté par piles
Luz de seguridad LED activada por movimiento y alimentada por baterías
Model / Model / Modelo #: SE1216-BRS-02LF4-G
(Page 1)
(Page 3)
(Page 5)
Hardware kit* / Trousse de quincaillerie* / Kit de aditamentos*
Required/ Nécessaire/ Obligatorio
AAx2
CCx2
AAx2
WARNINGS AND CAUTIONS
INSTALLATION
ENGLISH
* Actual hardware may differ from illustration./ * La quincaillerie incluse peut être différente de l’illustration. * Los aditamentos reales pueden diferir de los que se muestran en la ilustración.
Light head
Tête de la lampe
Cabeza de luz
Mounting base
Base de montage
Base de montaje
1/16 in.
0,16 cm
1/16 in.
0,16 cm
3/16 in.
0,48 cm
Masonry bit
3/16 in.
0,48 cm
Motion Sensor
Détecteur de mouvement
Sensor de movimiento
IMPORTANT SAFETY INFORMATION
1. LEDs can be damaged by electrostatic discharge (ESD) shock. Before installation, discharge yourself by touching a grounded bare metal surface
to remove this hazard. To avoid damage, do not remove the clear lens over the LED module.
2. NOT FOR EAVE MOUNTING ONTO PERFORATED EAVE MATERIAL: Mounting to anything other than a at surface can cause water to
seep into the xture which would then void the IP65 rating.
Fixture should be mounted 8-10ft high for the xed PIR to sense motion up to 40 feet away.
Make sure rubber grommets
are in place behind the screw
heads before screwing in to
insure proper water tight seal.
Make sure xture is locked tightly onto the mounting plate to
create a seal to prevent water from entering from the back.
READ ENTIRE INSTALLATION PROCEDURE BEFORE YOU BEGIN!
4 5
3
1
1
3
5
2
4
2
Remove the mounting plate by turning counterclockwise until it comes loose.
Locate the open holes for mounting at the midline of the mounting plate and drill a pilot hole in the center. If mounting onto brick or masonry, drill 3/16 in.
hole and place the masonry anchors (AA) in the pilot holes and hammer them into place until ushed with surface of masonry. Place washer (CC) over
the mounting hole and drive long screws (BB) into masonry anchor until snug. DO NOT OVERTIGHTEN. If mounting onto wood surface, drill 1/16 in.
hole and use the wood screws (BB) and washers (CC) provided to secure the mounting plate.
Remove the screw on the battery compartment cover. Remove the battery compartment cover.
Insert 3 new alkaline C cell batteries (not included) into the battery compartment and orient them with the “+” and “-” markings on the back of the battery
compartment. Re-attach the battery compartment cover by aligning the legs on the lower edge of the battery compartment cover onto the xture body
and close the cover until the catch at the top engages. Re-attach the screw. When ready to use, turn the switch, located below the battery compart-
ment, to “ON”. There will be an approximate 15 second delay for the xture to light up, even if there is motion. This will occur every time the xture is
turned “OFF” and back “ON” at the switch or the batteries are changed. Do not mix old and new batteries. Cold weather may have a negative impact on
battery life.
Attach the security light to the mounting plate by positioning the security light over the mounting plate at an angle. Engage the security light into the
grooves of the mounting base and secure by twisting clockwise until the security light is seated vertically.
AAx2
BBx2 CCx2
MASONRY
WOOD
CC C
OFF
ON
OFFOFF
ONON
OPEN LOCK
UPWARD
To Next Page
General
