GOSUNCN ME3630 Series

Need help?

Do you have a question about the GOSUNCN ME3630 Series and is the answer not in the manual?

Summary

Safety Information

Introduction to AT Commands

AT Command Syntax

ATI Request identification information

Command to request device identification information.

AT+GMI Request manufacturer identification

Command to request manufacturer identification.

AT+CGMI Request manufacturer identification

AT+GMM Request model identification

Command to request the specific model of the device.

AT+CGMM Request model identification

AT+GMR Request revision identification

Command to request version, revision, or date.

AT+CGMR Request revision identification

AT+GSN Request IMEI

Command to request the IMEI.

AT+CGSN Request IMEI

Command to request the IMEI without echo.

AT+CIMI Request international mobile subscriber identity

Command to request the IMSI.

AT+ZGETICCID Get the ICCID of (U)SIM

Command to request the ICCID of the SIM card.

AT+ZPCB Check PCB No.

General Commands

AT&F Set to Factory-defined Configuration

Resets parameters to manufacturer-defined defaults.

AT&V Display Current Configuration

AT&W Store AT command Setting to User Defined Profile

ATZ Reset to default configuration

Resets all parameters to factory defaults.

AT+CFUN Set Phone Functionality

Selects the level of MT functionality.

SIM Related Commands

AT+CLCK Facility Lock

Locks, unlocks, or interrogates MT or network facility.

AT+CPWD Change Password

Sets a new password for facility lock function.

AT+CPIN Enter PIN

Sends password to MT before operation (SIM PIN, PUK, etc.).

AT+CRSM Restricted SIM Access

AT+ZPINPUK Check PIN and PUK retry times

SMS Commands

AT+CSMS Select Message Service

Selects messaging service and returns supported message types.

AT+CMGF Message Format

Selects input/output format for messages (PDU or Text mode).

AT+CSCA Service Centre Address

Sets the Service Center Address for SMS transmissions.

AT+CSMP Set Text Mode Parameters

AT+CSAS Save Settings

AT+CRES Restore Settings

AT+CNMI New Message Indications to TE

AT+CMGL List Messages

Returns messages from storage based on status value.

AT+CMGR Read Message

Returns a message with location value from storage.

AT+CMGS Send Message

Sends a message from TE to the network.

AT+CMSS Send Message from Storage

Sends a message from preferred storage to the network.

AT+CMGW Write Message to Memory

AT+CMGD Delete Message

AT+CMGC Send Command

AT+CPMS Preferred Message Storage

AT+ZSPWAKEUP Enable;disable specified SMS remote wakeup function

Network Service Commands

AT+CREG Network registration

Controls presentation of network registration status codes.

AT+CEREG Network registration

AT+COPS Operator selection

Selects and registers the LTE network operator.

AT+CSQ Signal quality

Returns received signal strength and channel bit error rate.

AT+CPOL Preferred operator list

AT+ZCELLINFO Request the information about serving cell

Requests LTE cell information.

AT+ZLOCKCELL lock cell command

AT+ZSNT Configuration of Network Selection Mode

AT+ZSNTE Network Selection according to 2 G;3 G;4 G

AT+ZPAS Check Module Status

AT^SYSINFO Request System INFO

AT+ZBAND Band lock

AT+ZCDS -Query Serving Cell Information

AT+ZSRSP Query RSRP,RSRQ,SINR of the main cell

Queries RSRP, RSRQ, SINR of the main cell.

AT+ZRSP Query RSRP,RSRQ,SINR of LTE neighbour cell

AT+CGEQOS Define EPS quality of service

Specifies EPS Quality of Service parameters.

AT+ZMONI Get the information of main& neighbor cells

Gets information of main and neighbor cells.

Packet Domain Commands

AT+CGDCONT Define PDP Context

Specifies PDP context parameter values.

AT+CGATT PS attach or detach

Attaches or detaches MT from the Packet Domain service.

AT+CGACT PDP context activate or deactivate

Activates or deactivates specified PDP context.

AT+CGPADDR Show PDP address

AT+CGEREP Packet Domain event reporting

AT+CGSMS Select service for MO SMS messages

AT$QCPDPP Set PDP Authentication parameters

Sets PDP Authentication parameters (username/password).

AT+ZECMCALL Make ECM data call

Makes a data call based on ECM interface.

+ZECMCALL active report the state of auto-dial

AT+ZNVWRITE Enable auto-dial function

AT+ZNVREAD Query the state of auto-dial function

AT+ZSDHCPLEASE Amend DHCP LEASE TIME

GPS Relative Commands

AT+ZGINIT Initialization Location command

AT+ZGMODE Set location mode

AT+ZGFIXRATE Set location mode choice when reset GPS

AT+ZGQOS Set QOS for location

AT+ZGRUN Location mode choice

AT+ZGRST Reset GPS

Executes a GPS reset.

AT+ZGPSAPN Set AGPS APN

Sets the APN for AGPS.

AT+ZGPORT Set GPS information report port.

+ZGMEASURE Report satellites measurements

+ZGPSR Report Location Data

AT+ZGPSR Enable;Disable +ZGPSR report

AT+ZGNMEA Set the reported NMEA format of GPS data

Hardware Relative Commands

AT+CCLK Clock Management

AT+ZTURNOFF Turn Off the Modem

Shuts down the modem.

AT+ZRST RESET the Module

Resets the module.

AT+ZGPIO GPIO Pins Set command

AT+ZADCx Read pin ADCx value

AT+ZSWITCH Switch the port of module in different operation systems

AT+ZADB Open;close ADB port

AT+ZADSET Port Switch between RNDIS;NDIS in Windows System

AT+ZSDT Enable SIM card hot-plug function

AT+ZCHIPTEMP Get the temperature of pmic, xo, pa

TCP;IP Relative Commands

AT+ZIPCFG Set and Query the params of PS Call

Sets and queries parameters for PS Call.

AT+ZIPCALL Start or End PS Call

Starts or ends a PS Call.

AT+ZIPOPEN Establish TCP;UDP Connection

Establishes TCP/UDP connection with a remote server.

AT+ZIPCLOSE Close TCP;UDP Connection

Closes TCP/UDP connection.

AT+ZIPSEND TCP;UDP Send Data in ASCII format

Sends data in ASCII format over TCP/UDP.

+ZIPRECV TCP;UDP Data Receive

AT+ZIPSTAT Query Socket State

AT+ZIPSLCFG Set Parameters of TCP;UDP Server

AT+ZIPLISTEN Open;Close TCP;UDP Server

AT+ZIPFRWL Set TCP;UDP Internal Firewall

AT+ZIPSENDRAW send raw data

AT+ZIPCREATE Data transparent transfer

AT+ZDNSGETIP domain name resolution

AT+ZIPCONTEXT Switch PDP context

FTP Relative Commands

AT$ZPDPACT Activate;Deactivate PDP connection

Activates or deactivates a PDP connection for FTP.

AT$ZFTPCFG FTP Parameters Configuration

AT$ZFTPSIZE Get the Size of FTP File

AT$ZFTPGET File Download

Downloads FTP files.

AT$ZFTPPUT File Upload

Uploads files to an FTP server.

AT$ZFTPCLOSE Close FTP Service

HTTP Relative Commands

AT+ZHTTPURL Set URL of HTTP server

Sets the URL of the HTTP server.

AT+ZHTTPGET Send GET Request to HTTP Server

Sends a GET request to an HTTP server.

AT+ZHTTPPOST Send POST Request to HTTP Server

Sends a POST request to an HTTP server.

Extended Commands

AT+ZCLRACQ Clear the historical earfcn;uarfcn