To Next PageTo Next Page
Need help?Do you have a question about the GREAT PLANES ElectriFly TRITON2 and is the answer not in the manual?
Covers input/output voltages, current limits, battery types, and cell counts.
Highlights key functionalities like adjustable current, blue backlight, LiPo support, and safety features.
Covers misuse, water, vent blockage, overcharging, and unattended operation.
Explains connecting the 12V DC source, polarity, and recommended input.
Details power limits (90W charge, 20W discharge) and input protection circuits.
Describes the LCD, MENU CHANGE, BATT TYPE buttons, and ROTATING DIAL.
Details banana jacks, thermal probe jack, and available charge lead adapters.
Guides on identifying battery types, voltage, and capacity for correct setup.
Explains the purpose of the Main, Setup, and Data View menus for operation.
Covers connecting the adapter, battery, and navigating menus with the dial.
Details how to set and utilize memory slots for quick recall of battery settings.
Instructions for choosing battery type and initiating charge, discharge, or cycle.
Covers avoiding overheating, deep cycling, using correct functions, and storage.
How to select charge screens and adjust current settings for NiCd/NiMH.
Procedure to start peak charge, monitor progress, and understand completion.
Tips on charge current, cell types, temperature, and auto function for optimal charging.
How to select discharge screens and adjust current/cutoff voltage.
Procedure to start discharge, monitor progress, and understand completion.
Advice on discharge current, voltage, and battery condition evaluation.
How to choose cycle modes, set currents, and determine the number of cycles.
Procedure to initiate cycling and what to expect upon completion.
Explains periodic cycling benefits, delays, and battery condition assessment.
Crucial warnings about LiPo/Li-Ion cell volatility, fire hazard, and proper handling.
Steps to set the charger for either LiPo or Li-Ion battery types.
Explains the differences between balanced and non-balanced LiPo pack wiring.
How to access charge screens and set capacity/voltage for lithium batteries.
Procedure to start charge, safety limits, and notes on lithium charging.
How to access discharge screens and set current/cutoff voltage for lithium.
Procedure to start discharge, safety limits, and notes on lithium discharge.
Covers voltage limits, avoiding deep discharge, and specific handling for lead-acid.
How to access charge screens and set current/voltage for lead-acid batteries.
Procedure to start charge and notes on lead-acid charging.
How to access discharge screens and set current/cutoff voltage for lead-acid.
Procedure to start discharge and notes on lead-acid discharge.
How to select tones or turn off the buzzer for notifications.
Setting an automatic charge stop timer and display scale for temperature.
Setting a maximum battery temperature for automatic charge/discharge stop.
Adjusting peak detection timing and sensitivity for NiCd/NiMH.
Setting a cooling delay between charge and discharge portions of a cycle.
Setting maximum capacity input to automatically stop NiMH charge.
Using a short burst of charge after peak to maximize NiMH voltage.
How to access and browse charge, discharge, and cycle data screens.
Explains what Input, Output, Peak, Capacity, and Temperature data represent.
Lists common error messages and their corresponding troubleshooting steps.
Addresses issues like display, battery detection, and auto-stop failures with solutions.
Details the 1-year warranty terms and how to send the product for service.
Chart detailing how charge/discharge current is limited by voltage for maximum power.
General| Battery Types | NiCd, NiMH, LiPo, LiFe, Pb |
|---|---|
| Display Type | LCD |
| Trickle Charge | Yes |
| Input Voltage Protection | Yes |
| Reverse Polarity Protection | Yes |
| Balance Port | Yes |
| Input Voltage | 11-15V DC |
| Charge Current | 0.1-5.0A |
| Discharge Current | 0.1-1.0A |
| Cell Count | 1 - 6 cells (LiPo, LiFe), 1 - 15 cells (NiCd, NiMH) |
