18
Technical Information
Service Manual
12. I FEEL
Press this button to turn on I FEEL function. " " icon is displayed
on remote controller. The unit automatically adjust temperature
according to the sensed temperature. Press this button again to
cancel I FEEL function. " " icon will disappear.
Please put the remote controller near user when this function is
set.
Do not put the remote controller near the object of high
temperature or low temperature in order to avoid detecting
inaccurate ambient temperature.When I FEEL function is turned
on, the remote controller should be put within the area where
indoor unit can receive the signal sent by the remote controller.
13. T-ON/T-OFF
● T-ON button
"T-ON" button can set the time for timer on. After pressing this
button, " " icon disappears and the word "ON" on remote
controller blinks. Press "▲" or " " button to adjust TIMER ON
setting. After each pressing "▲" or " " button, TIMER ON setting
will increase or decrease 1min. Hold "▲" or " ▲ " button, 2s later,
the time will change quickly until reaching your required time.
Press "T-ON" to conrm it. The word "ON" will stop blinking. " "
icon resumes displaying. Cancel TIMER ON: Under the condition
that TIMER ON is started up, press "T-ON" button to cancel it.
● T-OFF button
"T-OFF" button can set the time for timer off. After pressing this
button," " icon disappears and the word "OFF" on remote
controller blinks. Press "▲" or " ▲ " button to adjust TIMER OFF
setting. After each pressing "▲" or " ▲ " button, TIMER OFF
setting will increase or decrease 1min. Hold "▲" or " ▲ " button,
2s later, the time will change quickly until reaching your required
time.
Press "T-OFF" word "OFF" will stop blinking. " " icon resumes
displaying. Cancel TIMER OFF. Under the condition that TIMER
OFF is started up, press "T-OFF" button to cancel it.
Note:
Under on and off status, you can set TIMER OFF or TIMER ON
simultaneously. Before setting TIMER ON or TIMER OFF, please
adjust the clock time. After starting up TIMER ON or TIMER OFF,
set the constant circulating valid. After that, air conditioner will be
turned on or turned off according to setting time. ON/OFF button
has no effect on setting. If you don’t need this function, please use
remote controller to cancel it.
14. WiFi
Press " WiFi " button to turn on WiFi function, " WiFi " icon will be
displayed on the remote controller.
Hold " WiFi " button for 5s to turn off WiFi function and " WiFi "
icon will disappear.
Under off status, press "MODE" and " WiFi " buttons
simultaneously for 1s, WiFi module will restore factory settings.
(This function is only available for some models.)
15. button
● Under unit off, press this button and hold for 3s to open the air
guide louver, icon is displayed in indoor unit. When air guide
louver is open to the maximum, and icon was disappear, you
could clean the unit. Cancel this function: Press and hold for 3s to
reset the air guide louver. If you press the power button directly,
the unit will be turned on.
16. CLOCK
Press CLOCK, blinking. Within 5 seconds, pressing ▲ or
button adjusts the present time. Holding down either button above
2 seconds increases or decreases the time by 1 minute every 0.5
second and then by 10 minutes every 0.5 second. During blinking
after setting, press CLOCK again t o conrm the setting and then
will be constantly displayed.
Function introduction for combination buttons
Energy-saving function
Under cooling mode, press "TEMP" and "CLOCK" buttons
simultaneously to start up or turn off energy-saving function. When
energy-saving function is started up, "SE" will be shown on remote
controller, and air conditioner will adjust the set temperature
automatically according to ex-factory setting to reach to the best
energy-saving effect.
Press "TEMP" and "CLOCK" buttons simultaneously again to exit
energy-saving function.
Note:
● Under energy-saving function, fan speed is defaulted at auto
speed and it can’t be adjusted.
● Under energy-saving function, set temperature can’t be
adjusted. Press "TURBO" button and the remote controller won’t
send signal.
● Sleep function and energy-saving function can’t operate at the
same time. If energy-saving function has been set under cooling
mode, press sleep button will cancel energy-saving function. If
sleep function has been set under cooling mode, start up the
energy-saving function will cancel sleep function.
Child lock function
Press "+" and "-" buttons simultaneously can turn on or turn off
child lock function. When child lock function is started up, " " icon
will be displayed on remote controller. If operate remote controller,
" "icon will ash three times, while remote controller won’t send
signal.
Switchover function for temperature display
After turning off the unit by remote controller, press "▼" and
To Next Page
Loading...
