GreenWorks LMF414 User Manual (English)

Questions and Answers:

R
Richard HernandezAug 13, 2025
Why does my GreenWorks Lawn Mower stop while mowing?
- M
  Michael LopezAug 13, 2025
  Your GreenWorks Lawn Mower might stop during mowing due to several reasons: the blade height might be too low, so try increasing it; the battery pack may be out of power, so ensure to charge it; grass clippings might be attached to the deck or the blade, in this case, remove the battery pack and check the deck; or the machine's operation temperature might be too high, so allow the machine to cool down.
E
Emma RobertsAug 17, 2025
What to do if my GreenWorks Lawn Mower does not start?
- U
  ugardnerAug 17, 2025
  If your GreenWorks Lawn Mower doesn't start, it could be due to a low battery. Try charging the battery pack. Alternatively, the battery key might not be inserted; make sure to put it in. If neither of these solutions works, the bail switch may be defective and need replacement.
J
Jonathan BradfordAug 20, 2025
Why does my GreenWorks Lawn Mower keep stopping during mowing?
- L
  lucasevelynAug 21, 2025
  If your GreenWorks Lawn Mower stops while mowing, it could be due to several reasons. The blade height might be too low, so try increasing it. The battery pack may be out of power; in this case, charge it. Grass clippings might be attaching to the deck or blade, so remove the battery pack and check the deck. Also, the machine's operating temperature could be too high; allow the machine to cool down.
R
rsalazarAug 25, 2025
Why is my GreenWorks LMF414 not mulching correctly?
- S
  Susan MillerAug 25, 2025
  If your GreenWorks Lawn Mower does not mulch correctly, wet grass clippings may be sticking to the deck, so wait until the grass dries before mowing. Alternatively, the mulch plug might be missing; install the mulch plug.
D
Deanna SmithAug 28, 2025
How to fix uneven cutting with my GreenWorks Lawn Mower?
- J
  Justin HillAug 28, 2025
  If your GreenWorks Lawn Mower cuts grass unevenly, the lawn might be rough, so examine the mowing area. Also, the blade height might not be set correctly; adjust the wheels to a higher position.
R
Russell GonzalezSep 1, 2025
Why is my GreenWorks Lawn Mower so hard to push?
- P
  Paul SosaSep 1, 2025
  If your GreenWorks Lawn Mower is hard to push, it could be because the grass is too tall or the blade height is too low. Increase the blade height to resolve this. Another reason could be that the grass catcher is full and the blade drags in thick grass, so empty the grass clippings from the grass catcher.
K
Kayla GreenSep 4, 2025
What to do if my GreenWorks LMF414 has a high vibration?
- L
  Loretta EllisSep 5, 2025
  If there is a high vibration in your GreenWorks Lawn Mower, the blade might be unbalanced or worn. If so, replace the blade. Another possible cause is a bent engine shaft. If you suspect this: 1. Stop the engine. 2. Remove the safety key and battery pack. 3. Disconnect the power source. 4. Inspect for damage. 5. Repair the machine before you start it again.
H
hubbarddanielSep 8, 2025
How to position the handle on a GreenWorks Lawn Mower?
- M
  Micheal FletcherSep 9, 2025
  If the handle of your GreenWorks Lawn Mower is not in position, the bolts may not be engaged correctly. Adjust the height of the handle and make sure that the knobs and bolts are aligned correctly.

GreenWorks LMF414 Specifications

General

Type	Cordless Lawn Mower
Motor Power	40V
Cutting Width	14 inches
Cutting Height Adjustment	5-position
Power Source	Battery
Battery Included	Yes
Charger Included	Yes
Mulching Capability	Yes
Battery Compatibility	GreenWorks G-MAX 40V
Battery Type	Lithium-Ion
Warranty	4-Year Limited Tool Warranty