Manually connect Manually connect
Connect to the router to take the
network configuration
Network configuration successful,
back to the plant
Manually connect Manually connect
Connect to the router to take the
network configuration
Network configuration successful,
back to the plant
AppendixⅠ.
Step7.
Check the status of datalogger
1.Log in your account, enter the my plant page, click the "+"to check the datalogger list
2.Edit, configure or delete the datalogger
Configure successfully, return to the plant page
Hotspot mode
Configuration boot
Step 01：Datalogger version detection
Step 02：Automatic upgrade
Step 03：Automatical restart after datalogger upgrade
Step 04：Reconnect to the datalogger hotspot
This step is only involved when the datalogger need to be updated
Hotspot mode
Configuration boot
Step 01 :Datalogger version detection
Step 02:Automatic upgrade
Step 03 :Automatical restart after datalogger upgrade
Step 04:Reconnect to the datalogger bluetooth
This step is only involved when the datalogger need to be updated
Frequently asked questions
1.Indicator Troubleshooting
When the ShineWiFi-X2 is working normally, click the
button on the ShineWiFi-X2 (The blue LED of ShineWiFi-
X2 will be always ON)
Enter the Bluetooth Mode;The Bluetooth Mode is
a debugging mode, non-professional people are
not suggested to use
When the ShineWiFi-X2 is in the Bluetooth Mode, click
the button on the ShineWiFi-X2(The blue LED of
ShineWiFi-X2 will quit the always ON state)
Press and hold for 6s until white light is on, then release
Reset the datalogger, restore factory settings
ShineWiFi-X2 not connected well with
inverter USB port
Check the connection status is well or not of the USB port
More than 3 minutes after the
configuration is complete, still
the green LED flashes
ShineWiFi-X2 has been connected to the
router but not connected to server
Check if home router is connected to the internet Check if
the router firewall allows to select port 7006
After configuration, blue LED
flashes
ShineWiFi-X2 communicates well with
inverter, router, and server
ShineWiFi-X2 module error
Need to replace a new ShineWiFi-X2
ShineWiFi-X2 can′t connect to the home
router
Check router information
Ÿ Router name should consist of English letters and
numbers, it does not support special symbols
Ÿ For safety reason, please use encrypted wireless
network
Ÿ It does not support public network that use secondary
authentication
Check if you filled in the correct name and password of the
home router when configuring it
ShineWiFi-X2 module is in Bluetooth
Mode
Which means the datalogger is in the Bluetooth Mode
2.ShineWiFi-X2 Button Description
Reset the datalogger?
A
Router change or the
password of router
change?
A
For the ShineWiFi-X2 that has been configured, when the router or
routerpassword is changed, the ShineWiFi-X2 needs to be reset before
configuration. Hold down the button on the datalogger for more than 6
seconds until the white LED light comes on. Then release the button
immediately. Start to reconfigure the network until the red light flashes
slowly.
Q
The supported charcters
for router and router
password
AQ
The datalogger has been
existed?
AQ
The router name and router password only support the combination of
number(0-9), letter(A-Z/a-z), and English punctuation
Ÿ The supported punctuation:(.,?!:@;+=#/()_-`^*&..$<>[]{});
Ÿ Unsupported punctuation:(﹉…·€'%¥\"");
Ÿ Router name and password can not have space symbol.
Go back to the application to the plant and find the datalogger list;
Click on the corresponding datalogger and configure it again;
If you can't find the datalogger, please contact with Growatt.
The indicator of WiFi- X2
shows it has been
disconnected
AQ
Check the status of the indicator of the datalogger, and deal with it according to
the following corresponding status The indicator lights out:
Ÿ Check if the inverter is on;
Ÿ Try to unplug the power;
Ÿ The indicator flashes green,indicating that the router has been connected,
not connected to the Internet;
Ÿ Please check your router settings or configure again;
Ÿ The indicator is green and always on, indicating that the router is not
connected / the signal is not good. Check whether the router is on or the
datalogger is far from the router;
Ÿ Indicator flashes red: please follow the manual to take the datalogger
configuration;
Ÿ Indicator is normally red, please contact the Growatt;
Ÿ Indicator is normally blue, indicating that the datalogger in the Bluetooth
Mode, try to press the button to switch to Standard Mode.
Supported router bands?
A
ShineWiFi-X2 only supports 2.4 GHz band WiFi signal, not 5GHz; please
check if the router's current band contains 2.4 GHz
QQ A
AQ
AQ
AQ
AQ
AQQ
Troubleshooting
AappendixⅡ.
GR-UM-278-A-00
Press the button for 6s until the indicator light is steady white, then
release to complete the reset.If you need to configure the datalogger,
please click the top right corner "+" of the ShinePhone in the "My plant"
page to enter the "datalogger list"then click the SN of datalogger to
ake the configuration.
.
Connect to the router to take the network configuration
To Previous Page
Loading...
Need help?
General
