To Next PageTo Next Page
Need help?Do you have a question about the Grundfos CR1 and is the answer not in the manual?
General| Series | CR |
|---|---|
| Model | CR 1 |
| Housing Material | Cast iron |
| Type | Centrifugal pump |
| Applications | Water supply, pressure boosting |
| Power Consumption | 0.37 kW |
| Frequency | 50 Hz / 60 Hz |
| Seal Material | EPDM |
Lists GRUNDFOS pump series (CR, CRI, CRN) and their associated model numbers.
Provides translations of 'Coupling/shaft seal' in various languages for service reference.
Presents an overall exploded view of the pump assembly for CR, CRI, CRN models 1, 3, and 5.
Illustrates the proper use of a tool for engaging the pump shaft.
Depicts an example of incorrect tool application for shaft engagement.
Diagram showing the correct procedure for installing the SV 2007 component.
Illustrates the process of applying lubricant to the pump shaft.
Shows the application of lubricant to the shaft seal area.
Diagram detailing the assembly of the SV 2007 component.
Specifies the mandatory torque value of 35 Nm for the assembly process.
Illustrates the application of oil to specific pump components.
Depicts using a tool for the final fitting of components.
Specifies the tightening torque for M6 bolts as 13 Nm.
Specifies the tightening torque for M8 bolts as 31 Nm.
Specifies the tightening torque for M10 bolts as 62 Nm.
Specifies the tightening torque for M5 bolts as 2.5 Nm.
Presents an overall exploded view of the pump assembly for CR, CRI, CRN models 10, 15, and 20.
Shows the first step of inserting a tool into the pump shaft.
Illustrates rotating the tool for proper shaft engagement.
Provides a cross-sectional diagram of the shaft seal assembly.
Specifies the torque requirement for M5 bolts in the seal assembly.
Illustrates the process of applying oil to a specific pump component.
Depicts the installation of a pump component.
Specifies the tightening torque for M6 bolts as 13 Nm.
Specifies the tightening torque for M8 bolts as 31 Nm.
Specifies the tightening torque for M10 bolts as 62 Nm.
Illustrates the correct fitting of a specific pump component.
Shows the sequential steps for assembling the pump.
Presents an overall view of the pump assembly for CR, CRN models 32, 45, 64, and 90.
Shows the installation procedure for the shaft engagement component.
Illustrates the installation of the sealing component.
Depicts the correct method for verifying shaft engagement.
Shows an incorrect method for verifying shaft engagement.
Provides a detailed diagram of the shaft engagement component.
Illustrates the process of lubricating the pump shaft.
Shows the application of lubricant to the shaft seal.
Demonstrates the method for installing the shaft seal.
Specifies the tightening torque for M6 bolts as 6 Nm.
Specifies the tightening torque for M10 bolts as 62 Nm.
Illustrates the steps for installing the pump seal.
Indicates a 1.7 mm measurement for proper seal fit.
Specifies the tightening torque for M10x25 bolts as 85 Nm.
Shows the first step of engaging a tool with the pump shaft.
Illustrates the removal of the tool after shaft engagement.
Presents an overall view of the pump assembly for CR, CRN models 120 and 150.
Shows the installation of a component for shaft engagement.
Illustrates engaging a tool with the pump shaft.
Illustrates the shaft engagement procedure for 11-45 kW pumps.
Illustrates the shaft engagement procedure for 55-75 kW pumps.
Shows component installation for 11-45 kW pumps.
Shows component installation for 55-75 kW pumps.
Illustrates the process of lubricating the pump shaft.
Shows applying Rocol 22 lubricant to the shaft seal.
Illustrates the shaft seal installation for 11-45 kW pumps.
Illustrates the shaft seal installation for 55-75 kW pumps.
Illustrates bolt tightening steps for 11-45 kW pumps.
Illustrates bolt tightening steps for 55-75 kW pumps.
Shows the first step of engaging the shaft engagement mechanism.
Illustrates the second step of engaging the shaft engagement mechanism.
Illustrates shaft engagement for 11-45 kW pumps.
Shows seal fitting for 55-75 kW pumps.
Specifies torque for 11-45 kW pumps: M10x25 bolts at 85 Nm.
Specifies torque for 55-75 kW pumps: M16x45 bolts at 100 Nm.
Shows the first step of engaging a tool with the pump shaft.
Illustrates confirming tool engagement with the pump shaft.
Diagram of the assembled pump for 11-45 kW models.
Diagram of the assembled pump for 55-75 kW models.
