EasyManua.ls Logo

H-ITT TX3100 User Manual

Default Icon
2 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
H-ITT TX3100 instruction manual
H-ITT 420 Shearer Blvd Cocoa, Florida 32922
The TX3100 is a radio frequency (RF) transceiver for use with H-ITT’s RF
BASE units.
The remotes do NOT need to be turned on or off, they are always ready to
respond when a key is pressed. In use, the indicator light will turn green
when the base unit has received your key press.
INSTALLING the Batteries
The TX3100
uses two standard AAA type batteries (not included).
Some models of the TX3100 have a slip on battery door, and some
models have 2 screws securing the battery door. To install batteries,
remove the battery door (either slip off or remove 2 screws where
indicated). Place the batteries in observing the polarity shown below.
Replace the battery door (if using screws, do not over-tighten). TX3100
recommended batteries: 1.5V, AAA size Alkaline, Energizer # LR03-AM4-
1.5V or equivalent.
TEST the Keys
With the batteries installed, press the >> key and notice the RED light blinks on then off. Repeat this test for << and the 10
data keys. The RED indicator light will blink on for about ½ second with each key pressed. Pressing the key will turn the
GREEN indicator light on for about 5 seconds, this is the receive function. If any of these tests fail, be sure the battery
installation is correct and making a good connection to the terminals, and make sure the battery cover is securely
attached to the case.
If you are in range of a H-ITT base receiver, the indicator will flash red, then turn green, which is an
acknowledgment that the signal was received.
Your Unique H-ITT ID number
Each remote has a unique ID number that is located in the battery compartment. (The TX3100 also has the ID number
labeled on the outside). Your instructor will need to record this ID number in the classroom software to associate you with
responses from your remote.
Rev 1.1
ID number on label
and also on the back
of battery door
Note, the battery
polarity when
installing batteries
Positive end this way
10 multiple choice
answer keys
Red/Green
indicator light; turns
green when your
answer is received
Forward and reverse
keys for scrolling to
paper test questions
Key to change
RF channel
Question and Answer IconNeed help?

Do you have a question about the H-ITT TX3100 and is the answer not in the manual?

H-ITT TX3100 Specifications

General IconGeneral
BrandH-ITT
ModelTX3100
Frequency2.4 GHz
Battery Type2 x AAA
TypeRemote Control
CompatibilityH-ITT response systems

Summary

TX3100 Battery Installation and ID Number

TX3100 Battery Installation Guide

Instructions for installing two AAA batteries, noting polarity and recommended types.

Remote ID Number Location and Purpose

Explains where to find the unique ID number and its importance for classroom association.

TX3100 Key Testing and Indicator Lights

How to Test TX3100 Remote Keys

Procedure for testing all keys using red and green indicator lights for feedback.

TX3100 RF Channel Management

Changing the TX3100 RF Channel

Steps to change the RF channel, valid numbers, and confirmation for classroom connection.

RF Channel Operation and Reset

Guidance on range, logging into classrooms, and battery removal resetting the channel.

TX3100 Remote Usage and Features

TX3100 Indicator Lights Explained

Describes the function of red and green indicator lights during remote operation.

Special Features and Transmitter Care

Covers <<, >> keys, special receive modes, and general advice on handling the transmitter.

TX3100 Specifications and Compliance

TX3100 Technical Specifications Summary

Details key technical data including dimensions, battery, RF carrier, channels, and range.

TX3100 FCC Compliance and Safety

Outlines FCC rules, conditions for operation, and warnings against modifications.