GENERAL PRODUCT INFORMATION
FEATURES
Safely stores most U.S and International SCBA brands and sizes.
Patented auto-lock system holds the SCBA securely in place.
Patented one-touch release handle (no straps or clamps to snag).
Easy adjust components.
Meets NFPA 1901 standards and requirements of EN 1846
SAFETY INFORMATION
DANGER indicates a hazardous situation which, if not avoided, WILL result in death or serious injury.
WARNING indicates a hazardous situation which, if not avoided, COULD result in a death or serious injury.
CAUTION indicates a hazardous situation which, if not avoided, COULD result in minor or moderate injury.
NOTICE is used to address practices not related to physical injury.
SAFETY INSTRUCTIONS (or equivalent) signs indicate specific safety related instructions or procedures.
TOOLS REQUIRED
TOP CLAMP
LOCKING NUT
PIVOT ARM LOCKING PLATE
WARNING LABEL
CENTER GUIDE
CYLINDER SUPPORT ASSEMBLY
VALVE CUP ATTACHMENT SCREW
CLAMP ADJUSTMENT SCREWS
QUICK HEIGHT ADJUSTMENT LEVER
LATCH ASSEMBLY
ALUMINUM MOUNTING CHANNEL
CENTER GUIDE ADJUSTMENT SCREWS
CYLINDER SUPPORT ATTACHMENT SCREWS
VALVE CUP (OPTIONS AVAILABLE)
Figure 1
SETUP AND ADJUSTMENT
AIR CYLINDER BRAND AND CYLINDER DIMENSION CHART
Identify air cylinder size before adjusting SecureALL
®
Table 1
CYLINDER TYPE DIAMETER CIRCUMFERENCE
VALVE CUP
NOTCH
POSITION
CYLINDER
SUPPORT
POSITION
TOP CLAMP
POSITION
BOTTLE SPECIFIC SERVICE KITS
SEE PAGE 2
AVON (ISI)
2216PSI ALUMINUM
6 ³
171mm
21 ¹
FRONT LOWER E
2216PSI COMPOSITE
6 ³
171mm
21 ¹
FRONT UPPER C
16
429mm
FRONT UPPER A
6 ³
161mm
20 ¹
FRONT LOWER B
60 MINUTE
6
21
FRONT LOWER C
DRAEGER
2216PSI ALUMINUM
6
171mm
21 ¹
FRONT LOWER E
2216PSI COMPOSITE
6
168mm
20 ¹
FRONT UPPER C
16
429mm
FRONT UPPER A
6 ¹
20
FRONT LOWER B
60 MINUTE
7''
178mm
FRONT LOWER C
HONEYWELL (SURVIVAIR, SPERIAN)
2216PSI ALUMINUM
6
171mm
21 ¹
FRONT LOWER E
2216PSI COMPOSITE
6 ³
171mm
21 ¹
FRONT UPPER C
6 ³
171mm
21 ¹
FRONT LOWER C
¹
140mm
17 ¹
FRONT UPPER A
6 ³
162mm
FRONT LOWER B
6 ³
171mm
21 ¹
FRONT UPPER C
60 MINUTE
178mm
FRONT LOWER C
INTERSPIRO
2216PSI ALUMINUM
6 ³
171mm
21 ¹
REAR LOWER E
2216PSI COMPOSITE
6
168mm
20 ¹
REAR UPPER C
¹
140mm
17 ¹
REAR UPPER A
6
160mm
19 ¹
REAR LOWER B
60 MINUTE
178mm
REAR LOWER C
MSA* M7 & G1 See page 2
2216PSI ALUMINUM
6 ³
171mm
21 ¹
FRONT UPPER E
2216PSI COMPOSITE
6 ³
171mm
21 ¹
FRONT UPPER B
6 ³
171mm
21 ¹
FRONT LOWER B
16
429mm
FRONT UPPER A
6 ³
19
494mm
FRONT LOWER B
6 ¹
19
498mm
FRONT LOWER B
60 MINUTE
7 ¹
181mm
22
FRONT LOWER C
127mm
¹
N/A UPPER A
18 ¹
478mm
N/A UPPER B
60 MINUTE
6
19
494mm
FRONT LOWER B
6
21
FRONT LOWER C
SCOTT* See page 2
2216PSI ALUMINUM
6
167mm
21 ¹
FRONT LOWER E
2216PSI COMPOSITE
6 ³
171mm
21 ¹
FRONT UPPER C
6 ³
171mm
21 ¹
FRONT LOWER C
16
429mm
N/A UPPER A
6
19
494mm
FRONT LOWER B
6 ¹
19
498mm
FRONT UPPER B
60 MINUTE
6
21
FRONT LOWER C
127mm
¹
N/A UPPER A
18 ¹
478mm
N/A UPPER B
60 MINUTE
6
19
494mm
FRONT LOWER B
6
21
FRONT LOWER C
VALVE CUP INSERT CHOICE BY BRAND
SECUREALL® BRACKET ADJUSTMENT INSTRUCTIONS
1. VALVE CUP ADJUSTMENT
Standard insert 8920-068 is factory installed on all SecureALL
®
brackets. See Figure 2.
VALVE CUP ADJUSTMENT FOR INTERSPIRO ONLY
Figure 2
1
2
REARFRONT
2. CYLINDER SUPPORT POSITION ADJUSTMENTS
1. Measure overall SCBA cylinder length (including valve).
use upper mounting holes.
use lower mounting holes as shown in Figure 4.
2. If applicable, remove attachment screws, position cylinder
support assembly, and reinstall screws.
UPPER
LOWER
WARNING
The installer is liable for SCBA bracket adjustment. Failure to properly tighten fasteners could
Figure 4
®
3. TOP CLAMP ADJUSTMENT
1. Measure the circumference of the SCBA bottle and refer to Table 1 for Top Clamp Position.
2. Place valve in foot cup and push bottle into SecureALL.
®
4. Replace and tighten adjustment screws in the appropriate clamp adjustment holes.
Remove and reinstall the SCBA assembly to confirm adjustment for cylinder size. Ensure there are no
obstructions that could prevent the cylinder from locking up against the clamp.
WARNING
Installer is liable for SCBA bracket adjustment. Failure to properly tighten fasteners could result
in clamp sliding forward and accidental SCBA release.
A
B
C
D
E
NOTICE: For additional assistance contact your OEM, dealer OR
H.O. BOSTROM COMPANY, INC.
818 PROGRESS AVE, WAUKESHA, WI 53186
WWW.HOBOSTROM.COM
ADJUSTMENT INSTRUCTIONS FOR THE
SECUREALL® SCBA LOCKING SYSTEM
TO BE REMOVED BY THE CUSTOMER ONLY
SECUREALL® BRACKET COMPONENTS
See Page 2
To Next Page
Need help?
General
