Why won't my hadewe HELIUS-40 equipment turn on?
If your hadewe Pedicure Spa equipment isn't turning on, there are a few things to check: * Make sure the cable is properly plugged into a working wall socket. * Verify that the main power button on the back of the unit is switched ON. * Try pulling the footswitch out of the socket to see if that resolves the issue.
Why is my hadewe HELIUS-40 handpiece vibrating and noisy?
If your hadewe Pedicure Spa handpiece is vibrating excessively or making a lot of noise, it could be due to: * Using bent tools or burrs. Try a different tool to see if this corrects the problem. * Exceeding the maximum allowed speed for the tool. Check the tool manufacturer’s recommended speed and decrease the speed on the control unit accordingly.
What to do if my hadewe HELIUS-40 Pedicure Spa burr stops suddenly?
If the burr on your hadewe Pedicure Spa stops suddenly, it may be due to the motor overheating. Let the unit rest for 10-15 minutes, then try again. If the motor then operates normally, try working with less pressure on the handpiece.
Why is my hadewe HELIUS-40 Pedicure Spa handpiece getting so hot?
If your hadewe Pedicure Spa handpiece is becoming very hot during operation, it is likely that too much pressure is being applied during use. Avoid pressing too hard; instead, let the tool do the work.
What to do if the suction stops suddenly on my hadewe Pedicure Spa?
If the suction in your hadewe Pedicure Spa stops suddenly, it could be that the suction motor is overheating. Check that the filter bag is not full and that there is no obstruction of airflow for the vacuum. Allow the motor to cool for 10-15 minutes and then try again.
Why is it difficult to insert a tool/burr into my hadewe HELIUS-40?
If you're having difficulty inserting a tool or burr into your hadewe Pedicure Spa, consider the following: * You might be using bent tools. Use a different tool to test this. * The chuck could be dirty. Clean the chuck according to the instructions in the manual.
What to do if my hadewe Pedicure Spa tool/burr does not spin?
If the tool or burr in your hadewe Pedicure Spa is not spinning, check these: * Ensure the chuck is not open. Slide the button on the handpiece back to lock the chuck. * Verify the chuck is tightened well, according to the instructions in the manual.
Why is the button on the handpiece of my hadewe HELIUS-40 hard to move?
If the button on the handpiece of your hadewe Pedicure Spa is difficult to move, the chuck may be dirty. Clean the chuck according to the instructions in the manual.
Instructions for safe and proper operation of the HELIUS-40, including setup and usage guidelines.
Key safety instructions and warnings to ensure user and patient safety during equipment operation.
Steps for correctly installing and preparing the HADEWE HELIUS-40 for use.
Detailed instructions on how to operate the HELIUS-40, including speed and suction settings.
Procedure for safely replacing the tool or burr in the handpiece chuck.
Guidance on adjusting speed and changing rotation direction for optimal performance.
Instructions for connecting and using the optional foot switch accessory.
Daily and post-treatment cleaning procedures for the HADEWE HELIUS-40 unit and handpiece.
Steps for replacing the suction filter bag to maintain optimal vacuum performance.
Periodic maintenance tasks, including filter exchange and sealing washer replacement.
Detailed instructions for disassembling and cleaning the handpiece components.
Procedure for cleaning the handpiece chuck to ensure proper tool insertion and operation.
Practical tips and warnings to prevent damage and ensure longevity of the handpiece.
Common problems, their probable causes, and recommended solutions for the HELIUS-40.
Power| power supply voltage | 115V AC |
|---|---|
| output power | 550W |
| voltage potential (output) | 5-27V |
Fuse Specifications| primary fuse F1 | 4.0A delayed-action |
|---|---|
| primary fuse F3 | 630mA delayed-action |
| secondary fuse | thermal |
Performance| suction capacity | 300-600 mmWs |
|---|---|
| noise level | <64dBA at 1m distance |
| protection class | 1 |
Weight and Dimensions| weight | 4.4 kg |
|---|---|
| width | 257 mm |
| height | 140 mm |
| depth | 257 mm |
Power| power supply voltage | 5-27V DC |
|---|---|
| speed range | 7000 – 40, 000 rpm |
Weight and Dimensions| weight | 160 g |
|---|---|
| length | 160 mm |
| handpiece diameter | 17.5 mm – 22 mm |
To Next Page