Hahnel Giga T Pro User Manual

Switching on your Giga T Pro
Insert CR2 battery into the receiver. Then press and “hold” button (3) for 3
seconds. The receiver is now ON.
Inbetriebnahme Ihres Giga T Pro
Legen Sie die CR2-Batterie in den Empfänger ein. Dann drücken und halten Sie
Taste 3 für 3 Sekunden. Der ist jetzt “ON” (eingeschaltet).
To Set Channel
Both transmitter and receiver must be set to the same channel (example “CH02”)
You may adjust the channel to avoid interference with another Giga T Pro or
similar wireless device
Einstellen des Kanals
Sender und Empfänger müssen beide auf den gleichen Kanal eingestellt werden
(z.B. “CH02”). Um eine … mit einem anderen Giga T Pro oder einem ähnlichen
drahtlosen Geräte zu vermeiden
To set channel on the receiver
Press (2) and (4) simultaneously.
Press (4) to set the receiver to Channel 02.
Press (2) and (4) simultaneously again to save setting.
Einstellen des Empfängerkanals
Dürcken Sie 2 und 4 gleichzeitig.
Drücken Sie 4 um den Empfänger auf Kanal 02 einzustellen.
Drücken Sie wieder 2 und 4 um die Einstellung zu speichern.
To set channel on the transmitter
The transmitter is already set to Channel “CH02”
If you want to change the channel
Press Joypad (12a) to set the transmitter to display CH mode (J)
Press centre button (11) to adjust channel. Use (12c) or (12d) to change channel
Press centre button (11) to save setting.
Einstellen des Senderkanals
Der Sender ist bereits auf Kanal “CH02” eingestellt.
Um den Kanal zu verstellen:
Drücken Sie 12a auf dem Joypad um auf dem Display CH mode J anzuzeigen
The Giga T Pro is now ready to use and can be connected to your camera
To turn off the receiver press and hold button (2) for 3 seconds
To save power, turn off when not in use
Der GigaT Pro ist jetzt einsatzbereit und kann mit Ihrer Kamera verbunden
werden.
Um den Empfänger auszuschalten halten Sie Taste 2 für 3 Sekunden gedrückt.

Hahnel Giga T Pro Specifications

General

Type	Wireless Remote Control
Frequency	2.4 GHz
Range	Up to 100m
Power Source	2 x AAA batteries
Timer Functions	Yes
Intervalometer	Yes
Display	LCD
Functions	bulb mode

Summary

Switching on your Giga T Pro

Setting the Channel

To Set Channel on the Receiver

Instructions for setting the Giga T Pro receiver channel, including saving the configuration.

To Set Channel on the Transmitter

Instructions for setting the Giga T Pro transmitter channel, including saving the configuration.

Standard Wireless Remote Control Functions

Single Shot Mode

Sets the transmitter for single shot mode, includes autofocus and shutter release instructions.

Sequential Shooting Mode

Sets the transmitter for sequential shooting mode, enabling continuous shots by holding the shutter button.

Bulb Mode - Long Exposures

Sets the transmitter for Bulb mode to capture long exposures, with instructions for autofocus and shutter control.

Continuous Shooting using Bulb Mode

Sets the transmitter for continuous shooting in Bulb mode, detailing shutter operation and display.

Basic Timer Mode

Configures the transmitter for basic timer functions like delay, number of shots, and saving settings.

Interval Timer Programmable Functions

DELAY (E)

Sets the delay time in hours, minutes, and seconds before interval shooting starts.

LONG (F)

Sets the time length for continuous shooting bursts or shutter open time in Bulb mode.

INTRVL (G)

Sets the interval time between consecutive shots in a sequence.

N (H) - Number of Shots

Sets the desired number of shots or exposures for the shooting sequence.

Programming Interval Shooting Modes

Interval Single Shots Programming

Guides on programming interval shooting for single shots, covering DELAY, LONG, INTVL, and N settings.

Interval Continuous Shooting Bursts Programming

Instructions for programming interval shooting for continuous bursts, covering DELAY, LONG, INTVL, and N.

Interval Long Exposure Shots Programming

Instructions for programming interval shooting for long exposures in Bulb mode.