Haier Room Air Conditioner - User Manual

Drawing for the installation of indoor and outdoor units
Necessary Tools for Installation
Hammerƽ
Torque wrench
ƽ
(17mm,22mm,26mm)
Nipperƽ
Reamerƽ
Hacksawƽ Pipe cutterƽ
Gas leakage detector orƽ
soap-and-water solution
Hole core drillƽ Flaring toolƽ
Spanner(17,19 and 26mm)ƽ Knifeƽ
Measuring tapeƽ
ƽ
ƽ
ƽ
ƽ
ƽ
Place where the distance of more than lm from televisions, radios, wireless apparatuses
and fluorescent lamps can be left.
ƽ
In the case of fixing the remote controller on a wall, place where the indoor unit can
receive signals when the fluorescent
ƽ
lamps in the room are in use.
ƽ
ƽ
ƽ
A distance marked
ƽ
Q
is available as illustrated in the below figure.
Before inserting power plug into receptacle, check the voltage without fail.
The power
sourceisthesameasthe
ƽ
corresponding name plate.
Install an exclusive branch circuit of the power.
ƽ
A receptacle shall be set up in a distance where the power cable can be
reached.
Donotextendthecablebycuttingit.
ƽ
Selection of Installation Place
Power Source
Preparation
NO.0010536242
Installation Manual of Room Air Conditioner
F
A
C
E
D
Optional parts for piping
Non-adhesive tape
Adhesive tape
Saddle (L.S) with screws
Connecting electric cable
forindoorandoutdoor
Drain hose
Heating insulating material
Piping hole cover
Floor fixing dimensions of the
outdoor unit
Fixing of outdoor unit
Fix the unit to concrete or blockƽ
with bolts (10mm) and nuts firmly
and horizontally.
When fitting the unit to wall
ƽ
surface, roof or rooftop, fix
a supporter securely with nails
orwiresinconsideration of
earthquake and strong wind.
If vibration may affect the
ƽ
house, fix the unit by attaching a
vibration-proof mat.
The marks from to
in the figure are the
parts numbers.
Thedistancebetween
theindoorunitandthe
floor should be more
than 2m.
ThemodelsadoptHCFCfreeref
rigerant R410A
more than
10cm (3 7/8)
more than 10cm
(3 7/8)
more than 10cm
(3 7/8)
more than 20cm
(7 7/8)
more than 15cm
(5 7/8)
more than 25cm
(9 7/8)
more than 60cm
(23 5/8)
A
G
ƽ
ƽ
A
F
C
E
D
G
B
Arrangement of piping
directions
Rear left
Left
Rear
right
Right
Below
G
Attention must be paid to
the pitch of drain hose
The above picture is for your reference only. Your product may look different.
Read this manual before installation.
Explain the operation of the unit to the user according to this manual.
Indoor Unit - Select a location that is
Outdoor Unit - Select a location that is
Robust not causing vibration, where the body can be supported sufficiently.
Not affected by heat or steam generated in the vicinity, where inlet and outlet of the
unit are not disturbed.
Possible to drain easily, where piping can be connected with the outdoor unit.
Where cold air can be spread in a room evenly.
Nearby a power receptacle. (Refer to drawings).
Less affected by rain or direct sunlight and is sufficiently ventilated.
Strong enough to bear the unit, where vibration and noise are not increased.
(4 1/2)
For:24k
Not causing a nuisance to neighbors due to discharged air or noise.
(10 1/16)
(5 1/2)
(19 2/3)
(5 1/2)
(24 7/8)
(4 1/2)
(13 1/2)
140 500
140
256
113.5
113.5
633
340
For:09k 12k 18k
(Unit:mm / inch)

Summary

Preparation

Necessary Tools for Installation

Lists essential tools for air conditioner installation, including drills, wrenches, and cutters.

Power Source Requirements

Details electrical power requirements, branch circuits, and receptacle placement for safe operation.

Installation Place Selection

Guides on choosing indoor and outdoor unit locations considering ventilation, support, and noise.

Indoor Unit Installation Steps

Mounting Plate and Wall Hole Fitting

Instructions for fitting the mounting plate and positioning the wall hole for indoor unit installation.

Piping Hole Cover Installation

Guidance on creating the wall hole and installing the piping hole cover for the unit.

Indoor Unit Piping Methods

Details different piping directions like rear and left-rear piping for indoor unit connection.

Electrical Wiring and Connections

Indoor and Outdoor Unit Wiring

Specifies power and control cable requirements for various indoor and outdoor unit models.

Outdoor Unit Connection

Instructions for connecting power supply and unit wire harness to the terminal board.

Refrigerant Piping and System Checks

Cutting and Flaring Piping

Details the process for cutting refrigerant pipes and performing flare work for R410A.

Drainage Installation

Ensures proper downward slope for the drain hose to prevent water pooling or odors.

Gas Leakage and System Checks

Procedure to check for gas leakage, perform vacuuming, and verify system operation.

Haier Room Air Conditioner Specifications

General

Brand	Haier
Model	Room Air Conditioner
Category	Air Conditioner
Language	English