Hak5 WiFi Pineapple Mark VII

To Next Page

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning

(Part 15.21) Changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s authority to operate

the equipment. RF Exposure (OET Bulletin 65) To comply with FCC RF exposure requirements for mobile transmitting devices, this transmitter

should only be used or installed at locations where there is at least 20cm separation distance between the antenna and all persons.

Information to the User - Part 15.105 (b) Note: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: * Reorient or

relocate the receiving antenna. * Increase the separation between the equipment and receiver. * Connect the equipment into an outlet on a

circuit different from that to which the receiver is connected. * Consult the dealer or an experienced radio/TV technician for help.

WiFi Pineapple is a trademark of Hak5 LLC. This product is packaged with a limited warranty, the acceptance of which is a condition of sale.

See Hak5.org for additional warranty details and limitations. Availability and performance of certain features, services and applications are

device and network dependent and may not be available in all areas; additional terms, conditions and/or charges may apply. All features,

functionality and other product speciﬁcations are subject to change without notice or obligation. Hak5 LLC reserves the right to make changes

to the products description in this document without notice. Hak5 LLC does not assume any liability that may occur due to the use or

application of the product(s) described herein. Made in China. Designed by Hak5 LLC, 548 Market Street, #39371, San Francisco, CA, 94104.

STATEMENT OF CONDITIONS

USB Host Port

USB-C Power /

Ethernet Port

Status LED

Reset Button

WiFi Pineapple Mark VII

Access from anywhere online.

Free download at https://c2.hak5.org

Connect to a 2-Amp USB power source.

Join the “Pineapple_XXXX” WiFi Network.

Browse to http://172.16.42.1:1471 and

follow the on-screen instructions.

Your WiFi Pineapple can also be provisioned

with a specially formatted USB flash disk, or by

connecting it to a computer using a USB cable.

Learn more at https://docs.hak5.org.

Need help?

Do you have a question about the Hak5 WiFi Pineapple Mark VII and is the answer not in the manual?

Summary

Safety Information and Warnings

The WiFi Pineapple Mark VII is a network administration and pentesting tool designed for authorized auditing and security analysis. It complies with Part 15 of the FCC Rules, indicating that its operation is subject to two conditions: it must not cause harmful interference, and it must accept any received interference, including that which may cause undesired operation. Users are cautioned that changes or modifications not expressly approved by the responsible party could void their authority to operate the equipment. For RF exposure compliance, the device should be used or installed at locations with at least a 20cm separation distance between the antenna and all persons.

The device is designed to provide reasonable protection against harmful interference in residential installations. It generates, uses, and can radiate radio frequency energy. If it causes harmful interference to radio or television reception, users are encouraged to try corrective measures such as reorienting or relocating the receiving antenna, increasing separation between the equipment and receiver, connecting the equipment to a different circuit, or consulting a dealer or experienced radio/TV technician.

The WiFi Pineapple Mark VII is a trademark of Hak5 LLC and comes with a limited warranty, the acceptance of which is a condition of sale. Additional warranty details and limitations can be found on Hak5.org. The availability and performance of certain features, services, and applications are device and network dependent and may not be available in all areas, with additional terms, conditions, and/or charges potentially applying. All features, functionality, and other product specifications are subject to change without notice or obligation. Hak5 LLC reserves the right to make changes to the product description in this document without notice and does not assume any liability for the use or application of the product(s) described herein.

Function Description:

The WiFi Pineapple Mark VII is primarily a network administration and pentesting tool. It is intended for authorized auditing and security analysis purposes only, subject to local and international laws where applicable. Users are solely responsible for compliance with all laws of their locality. Hak5 LLC and its affiliates disclaim responsibility for unauthorized or unlawful use.

Important Technical Specifications:

Interfaces: (3) WiFi, (1) USB 2.0, (1) USB-C Ethernet
Standards: USB 2.0, 802.11b/g/n
Dimensions: 107 x 93 x 21 mm
Frequency Range: 2.412 ~ 2.4835 GHz
Power: 10W (USB 5V 2A)
Operating Temperature: 35°C ~ 45°C
Storage Temperature: -20°C ~ 50°C
Relative Humidity: 0% to 90% (noncondensing)
Components: WiFi Pineapple Mark VII device, USB-C Cable, (3) RP-SMA Antennas, and a product information card.

Usage Features:

Power Source: Connects to a 2-Amp USB power source.
Network Connection: Joins the "Pineapple_XXXX" WiFi Network.
Setup and Configuration: Users can browse to http://172.16.42.1:1471 and follow on-screen instructions for setup.
Provisioning: The device can be provisioned with a specially formatted USB flash disk or by connecting it to a computer using a USB cable.
Cloud C2 Enabled: Offers access from anywhere online, with a free download available at https://c2.hak5.org.
Status LED Indications:
- Blinking Blue: Starting up
- Solid Blue: Ready
- Solid Red: Invalid USB Files
- Alternating Blue/Red: Flashing Firmware (users are warned not to unplug power during this state).
Physical Ports: Includes a Reset Button, Status LED, USB Host Port, and a USB-C Power / Ethernet Port.

Maintenance Features (Safety and Care):

Heat Management: The device may get hot to the touch, which is normal. If it becomes too hot, unplug it and allow it to cool before handling. It complies with applicable surface temperature standards (IEC 60950-1).
Ventilation: Keep the device in a well-ventilated area during use, allowing for adequate air circulation.
Environmental Conditions: Do not expose the device to water or extreme conditions such as excessive moisture, heat, cold, or dust, as this can cause malfunction.
Disassembly and Repair: Users are advised not to attempt to disassemble or repair the device themselves, as doing so voids the limited warranty and could harm the device or user.
Hazardous Environments: The device is not designed, manufactured, or intended for use in hazardous environments requiring fail-safe performance where failure could lead to death, personal injury, or severe physical or environmental damage.

Full documentation for the WiFi Pineapple Mark VII is available at https://docs.hak5.org.