To Next PageTo Next Page
Need help?Do you have a question about the Hama 047454 and is the answer not in the manual?
Provides essential safety precautions for using the SAT finder, including protection from moisture and working at heights.
Guides users through connecting the SAT finder, adjusting sensitivity, and fine-tuning the antenna for the strongest signal.
Provides essential safety precautions for using the SAT finder, including protection from moisture and working at heights.
Guides users through connecting the SAT finder, adjusting sensitivity, and fine-tuning the antenna for the strongest signal.
The Hama SAT Finder is a compact and essential tool designed to assist users in accurately aligning their satellite dish for optimal signal reception. This device simplifies the often complex process of satellite dish installation and adjustment, making it accessible even for those without extensive technical knowledge.
The primary function of the Hama SAT Finder is to detect and measure the strength of incoming satellite signals, providing visual and auditory feedback to guide the user during dish alignment. It acts as an intermediary device, connecting between the Low Noise Block (LNB) converter on the satellite dish and the satellite receiver. By doing so, it allows for real-time monitoring of the signal strength as the dish is adjusted.
The device features a signal strength display, typically a needle gauge, which visually indicates the intensity of the received signal. As the satellite dish is moved, the needle on this gauge will respond, rising as the signal strengthens and falling as it weakens. Complementing the visual feedback, the SAT Finder also emits an audible tone. This tone changes in pitch or intensity in correlation with the signal strength, providing an additional sensory cue that allows users to make fine adjustments without constantly looking at the display.
A key component of the SAT Finder is its sensitivity controller. This knob allows the user to adjust the device's responsiveness to the signal. In situations where the signal is very strong, the sensitivity can be reduced to prevent the gauge from maxing out, enabling more precise fine-tuning. Conversely, if the signal is weak, increasing the sensitivity can help in initially locating the satellite.
The device is powered by the satellite receiver itself, drawing a small amount of current through the coaxial cable. This eliminates the need for external batteries or power adapters, enhancing its portability and ease of use in various outdoor settings.
The Hama SAT Finder is designed for straightforward operation, guiding users through a step-by-step process to achieve the best possible satellite reception.
Initial Setup: Before beginning the alignment process, the SAT Finder is connected in-line between the LNB and the satellite receiver using a short F-cable. It's crucial to ensure the satellite receiver is disconnected from the power supply during this initial connection to prevent any electrical hazards. Once connected, the receiver is reconnected to power, and a suitable channel is selected to provide a signal for the SAT Finder to detect.
Rough Alignment: The first step in alignment involves a rough positioning of the satellite dish. This is typically done using a protractor and compass to approximate the correct azimuth and elevation angles for the desired satellite, based on the user's geographical location. Once the dish is roughly pointed, the SAT Finder's sensitivity controller is adjusted until the signal level on the display shows an initial jump, indicating that some signal is being received.
Fine-Tuning: With a rough alignment established, the user then slowly and methodically turns and pans the satellite antenna. During this process, both the visual display and the audible tone of the SAT Finder provide immediate feedback. As the dish approaches the optimal position for the desired satellite, the needle on the gauge will rise, and the audible tone will become stronger or higher in pitch. The goal is to find the position where the signal strength is at its maximum.
Optimizing Sensitivity: If the signal strength reaches the maximum "10" on the display, the sensitivity controller should be turned down. This reduces the device's sensitivity, allowing the user to continue making finer adjustments and pinpoint the absolute peak signal without the gauge being saturated. Once the sensitivity is adjusted, the user continues to fine-tune the antenna to achieve the highest possible reading, ideally close to the maximum "10" mark.
Securing the Dish: After achieving the optimal signal strength, the antenna fasteners are tightened to secure the dish in place. A critical point to remember is that tightening these fasteners can sometimes slightly alter the dish's position, potentially causing a drop in signal strength. Therefore, it is recommended to recheck the signal on the SAT Finder after tightening and make any necessary minor adjustments.
Final Verification: Once the dish is securely fastened and the SAT Finder indicates maximum signal, the user can verify reception on their satellite receiver. This involves checking if the desired satellite channels are now being received clearly. If successful, the SAT Finder can then be removed, and the LNB can be reconnected directly to the satellite receiver.
The Hama SAT Finder is designed for durability and minimal maintenance, focusing on protecting the device from environmental factors and ensuring its longevity.
Protection from Moisture: One of the most important maintenance considerations is to protect the SAT Finder from moisture. As an electronic device often used outdoors, exposure to rain, dew, or high humidity can damage its internal components. Users should ensure the device is kept dry during use and stored in a dry environment when not in operation.
Temporary Installation: The SAT Finder is intended for temporary installation only. It should not be left permanently installed between the SAT dish and the receiver. Prolonged exposure to outdoor elements, even if protected from direct moisture, can lead to wear and tear, and it is not designed for continuous operation in an outdoor environment. Removing it after alignment helps preserve its functionality and extends its lifespan.
Safe Handling: When working on a roof or at elevated heights to adjust the satellite dish, proper safety precautions are paramount. This includes using appropriate safety gear and ensuring stable footing to prevent falls. The SAT Finder itself requires no special handling beyond careful connection and disconnection of the F-cables to avoid damaging the connectors.
Professional Assistance: In cases of doubt or if the user is uncomfortable working at heights or performing the alignment, it is strongly advised to contact a qualified technician. Attempting to mount or adjust the product without proper knowledge or safety measures can lead to personal injury or damage to the equipment. The SAT Finder is a tool to assist, but it does not replace the need for safe practices or professional expertise when required.
By adhering to these usage and maintenance guidelines, users can effectively leverage the Hama SAT Finder to achieve reliable satellite reception and ensure the device remains in good working condition for future use.
General| Type | Tripod |
|---|---|
| Material | Aluminium |
| Weight | 1.2 kg |
| Product Type | Tripod |
| Thread | 1/4 (6.4 mm) |
| Compatibility | Cameras, camcorders |
| Colour | Silver |
| Color | Silver |
