Harman Kardon Citation II - Page 14

12
Check
( )
( )
Connect a white wire 19
¾
˝ long from 9 (
⅜
˝) to 58 (
¼
˝).
( )
( )
Connect an HI red wire 10
¾
˝ long from 38 (
⅜
˝) to 13 (
⅜
˝).
( )
( )
Connect an HI red wire 8
½
˝ long from 39 (
⅜
˝) to 44 (
¼
˝).
( )
( )
Connect an HI yellow wire 8
½
˝ long from 37 (
⅜
˝) to 43 (
¼
˝).
( )
( )
Connect an HI orange wire 9˝ long from 46 (
¼
˝) to 49 (
⅜
˝).
( )
( )
Connect a black wire 10˝ long from 41 (
⅜
˝) to 48 (
⅜
˝).
( )
( )
Connect a gray wire 20
½
˝ long from 60 (
¼
˝) to 63 (
¼
˝).
( )
( )
Connect a gray wire 12
¼
˝ long from 51 (
¼
˝) to 59 (
¼
˝).
( )
( )
Tape the harness tightly at the place indicated.
THIS COMPLETES THE WIRING OF THE HARNESS. It will be installed at a later time. Keep harness
on board till ready for use.
PRELIMINARY TERMINAL BOARD WIRING
Refer to Pictorial #3.
TB1 and TB2 are identical and may be wired simultaneously to save time. When each step has been per -
formed on one, it should then be performed on the other.
Connect jumpers to lower section of lugs using bare wire. Note that each lug is numbered and for easy
identification, the jumpers are screened on the board. Wrap wire one full turn. See Figure A.
Check
TB1
TB2
( )
( )
( )
10 (NS) to 11 (S) to 12 (S).
( )
( )
( )
14 (NS) to 43 (NS).
( )
( )
( )
45 (S) to 20 (NS).
( )
( )
( )
42 (NS) to 23 (NS).
( )
( )
( )
9 (NS) to 40 (S) to 28 (NS).
( )
( )
( )
38 (S) to 29 (NS).
( )
( )
( )
36 (NS) to 31 (S).
( )
( )
( )
35 (S) to 34 (NS).
( )
( )
( )
41 (S) to 25 (NS).
( )
( )
( )
18 (NS) to 19 (NS).
The following wires are connected to the lugs from the rear of the board through the holes designated by a
letter. Cut to size and strip
⅜
˝ at each end. Refer to Figure B.
( )
( )
( )
Yellow 5˝ F-36 (S) to G-44 (S).
( )
( )
( )
Blue 4
½
˝ M-37 (S) to B-43 (S).
( )
( )
( )
Blue 4
¾
˝ C-24 (NS) to H-46 (S). Route as shown.
( )
( )
( )
Blue 3
¾
˝ C-24 (NS) to N-7 (S).
( )
( )
( )
Yellow 4
½
˝ A-5 (S). Leave other end free.
( )
( )
( )
Yellow 4
½
˝ L-39 (NS). Leave other end free.
( )
( )
( )
Take one of the 14˝ precut shielded wires and unwrap the shield from the inner conductor.
Twist the resulting strands of wire together. Strip
⅜
˝ from the inner conductor insulation and
tin the lead and the shield. Pass the shielded lead through hole D and connect the inner wire to
Pin-27 (NS). Connect the shield to Pin-28 (S). Strip the other end of the shielded lead in the
same manner and leave free. It will be connected later on.
Refer to Pictorial #3, Figure C.