EasyManua.ls Logo

Harman Kardon PM655 - Tape Recording and Playback; Tape Dubbing Procedures

Harman Kardon PM655
11 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
Tape
Recording
Recording
from
a
program
source
(FM/AM
broadcast.
turntable
or
components
connected
to
the
VIDEO/CD
jacks)
on
a
tape
deck
connected
to
the
TAPE
1
and/or
TAPE
2
jacks:
1.
Turn
the
VOLUME
control
knob
to
the
minimum
level
and
press
the
POWER
switch.
The
POWER
indicator
lights
up.
2.
Set
the
SPEAKER
selector
for
the
desired
speaker
system(s).
3.
Select
the
desired
program
source
with
the
FUNCTION
selector.
The
function
indicator
lights
up
to
indicate
the
program
source
selected.
4.
Set
the
TAPE
OUT
selector
to
the
“source”
position.
.
Set
the
TAPE
MONITOR
selector
to
the
“source”
position.
6.
Advance
the
VOLUME
control
knob
to
a
comfortable
level.
7.
lf
the
program
source
mode
is
monaural,
press
the
MODE
switch
to
the
“mono”
position
according
to
the
mono
program
source.
8.
Start
recording
by
activating
the
tape
deck(s)
connected
to
the
TAPE
1
and/or
TAPE
2
jacks.
The
source
sound
can
be
listened
to
from
the
speakers
or
headphone.
9.
To
monitor
the
sound
being
recorded,
set
the
TAPE
MONITOR
selector
to
the
“tape
1”
or
“tape
2”
position
according
to
the
tape
deck
being
recorded.
The
tape
monitor
indicator
will
light
up,
indicating
the
monitoring
state.
ol
NOTE:
Recording
onto
the
tape
deck
is
carried
out
directly
from
the
program
source
without
being
influenced
by
the
volume,
balance,
bass
and
treble
controls,
bass
and
treble
turnovers,
tone
defeat,
bass
contour,
subsonic
and
high
cut
filter
switches
of
this
unit.
Air
check
can
be
made
while
listening
to
other
program
source.
1.
Turn
the
VOLUME
control
knob
to
the
minimum
level
and
press
the
POWER
switch.
The
POWER
indicator
lights
up.
2.
Set
the
SPEAKER
selector
for
the
desired
speaker
system(s).
.
Set
the
FUNCTION
selector
to
the
“tuner”
position.
.
Set
the
TAPE
MONITOR
selector
to
the
“source”
position.
.
Activate
the
tuner
and
tune
to
broadcast
frequency.
.
Set the
TAPE
OUT
selector
to
the
“tuner”
position.
.
Start
recording
by
activating
the
tape
deck(s)
connected
to
the
TAPE
1
and/or
TAPE
2
jacks.
The
broadcast
sound
can
be
listened
to
from
the
speakers.
8.
Select
the
desired
program
source
with
FUNCTION
slelector.
The
new
sound
source
will
be
heard
from
the
speakers.
NOOR
W
OPERATIONS
Tape
Playback
1.
Turn
the
VOLUME
control
knob
to
the
minimum
level
and
press
the
POWER
switch.
The
POWER
indicator
lights
up.
2.
Set
the
SPEAKER
selector
for
tne
desired
speaker
system(s).
.
Set
the
TAPE
OUT
selector
to
the
“off”
position.
4.
Set
the
TAPE
MONITOR
selector
to
the
“tape
1”
or
“tape
2”
position
corresponding
to
the
tape
deck
to
be
played.
The
tape
1
or
2
monitor
indicator
will
light
up.
5.
Insert
a
recorded
tape
in
the
tape
deck
and
set
the
tape
deck
in
the
playback
mode.
6.
Advance
the
VOLUME
contro!
knob
to
a
comfortable
level
and
adjust
the
BASS
and
TREBLE
control
knobs
as
desired.
7.
Activate
the
BALANCE
control
knob,
BASS
TURNOVER,
TREBLE
TURNOVER,
TONE
DEFEAT,
BASS
CONTOUR,
HIGH
CUT
filter
or
MODE
switch
if
necessary.
w
Tape
Dubbing
Two
tape
decks
can
be
connected
to
this
unit
and
dubbing
can
be
done
from
either
tape
deck
to
the
other.
Dubbing
from
tape
deck
1
to
tape
deck
2
1.
Turn
the
VOLUME
contro!
knob
to
the
minimum
level
and
press
the
POWER
switch.
The
POWER
indicator
lights
up.
2.
Set
the
SPEAKER
selector
for
the
desired
speaker
system(s).
3.
Set
the
TAPE
OUT
selector
to
the
“copy-1
to
2”
position.
4.
lf
the
program
source
mode
is
monaural,
press
the
MODE
switch
to
the
“mono”
position.
5.
After
setting
the
tape
deck
1
connected
to
the
TAPE
1
jacks
for
playback,
and
the
tape
deck
2
connected
to
the
TAPE
2
jacks
for
recording,
dubbing
will
begin.
6.
To
monitor
the
sound
being
played,
set
the
TAPE
MONITOR
selector
to
the
“tape
1”
position.
To
monitor
the
sound
being
recorded,
set
the
TAPE
MONITOR
selector
to
the
“tape
2”
position.
Dubbing
from
tape
deck
2
to
tape
deck
1
1.
Set
the
TAPE
OUT
selector
to
the
“copy-2
to
1”
position.
2.
Dubbing
will
begin
by
setting
the
tape
deck
2
connected
to
the
TAPE
2
jacks
to
playback
and
the
tape
deck
1
connected
to
TAPE
1
jacks
to
record.
Another
program
source
(phono,
tuner,
video/CD)
can
be
listened
to
during
dubbing,
with
no
effect
on
the
dubbing
quality.
1.
Setthe
TAPE
MONITOR
selector
to
the
“source”
position.
2.
Select
the
desired
program
source
with
the
FUNCTION
selector.

Table of Contents

Other manuals for Harman Kardon PM655

Preview: Technical Manual
Technical Manual28 pages

Related product manuals