EasyManua.ls Logo

Harman JBL BassPro 12 - Specifications and Troubleshooting; Specifications; Troubleshooting

Harman JBL BassPro 12
6 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
SPECIFICATIONS
an-
Complement. 12"
(300mm)
subwoofer
Amplifier
Power
Output: 150 watts
RMS,
450 watts peak
Frequency
Response:
30
Hz
- 200
Hz
Maximum
Current
Draw:
20A
Quiescent
Current
Draw:
<0.9A
Input
SenSllivlty:
0.065 V - 2.0 V line-level input;
0.35
V-10Vhigh-level
input
Crossowr
Frequency:
40 Hz - 200
Hz
Crossowr
Slope:
12 dB/octave
Bass
Boost:
0
dB
to + 12
dB
@ 45Hz
Fuse:
25A
DimenSKlnS
(jV X H X
D):
22-1
/2"
X
14-5/8"
X
9·3/16"
D1,
12-1/6"
D2 (570mm x
371mmx
232mm
D1;
305mm
D2)
Weight
34
3
lb.
(15.56
kg)
~
HARMAN
~
3
HARMAN
International lndustnes,
Incorporated 8500 Balboa Boulevard,
Northridge,
CA
91329
USA
www.jbl.com
TROUBLESHOOTING
No audio and POWER indicator
is
off.
No
\/Oltage
at
BATT+
and/or REM terminals,
or
bad or no ground
connec•
ban.
Check IIOltages at amplifier terminals wrth
VOM.
No audio and PROTECT indicator illuminated.
DC
\/Oltage
on amplifier output. Amplifier may need service; see
enclosed
warranty card for serv,ce
1nformat1011.
No audio and PROTECT and POWER indicators illuminated.
Voltage
less than
9V
on
BATT+
connecbon. Check vehicle charging system.
No
audio and PROTECT indicator is on.
Amplifier is ovemeated.
Make
sure amplifier cool,ng
IS
not blocked at
mooning location.
Or,
there may be
\/Oltage
greater
than
16V
(or
less
than
9V)
on
BATT+
connecbon. Check vehlcie
charging
system.
Amplifier fuse keeps blowing.
The
wInng
Is connected incorrectly
or
there is a short circuit. Check
wInng
connections.
Distorted audio.
GAIN
IS
not set
properly.
Check sett,ng. Check wires for
shorts
or grounds.
Amplifier or source
unrt
may
be
defective.
Music lacks dynamics
or
"punch
.•
If
us,ng
speaker-level inputs, check
connectJOOS
for proper polarity. Switch
PHASE
back
and
forth between
and
180°
and
leave
on setting
wrth
best
sound.
Engine
noise-whining
or
clicking-in
system when
the
engine is on.
Amplifier
is
picking
up
alternator noise. First, check ground
connect1011
on the amplifier - a loose
or
1111proper
ground
IS
one of the
ma,n
causes
for noise.
Tum
down
GAIN. Move RCA audio cables away from fXJN8f
wires. Installing an alternator noise filter on fXJN8f
line
between battery
and
alternator might
also
be
necessary.
Cl
2019
HARMAN
International Industries, Incorporated.
All
rights
reserved.
JBL
1s
a trademark
of
HARMAN
International Industries, Incorporated,
registered
in
the
United States and/or other countries.
Features
,
spec1f,cat1ons
and
appearance
are
subJect
to change without notice.

Related product manuals